Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Push bolts into holes on front of handle. If bolts will not go through hole easily handle is not pushed completely down. 1-3 1-6 1-9 1-4 1-5 1-7 1-8 When handle sections are completely together, squeeze trigger (C) and depress Clean Surge™ Button (D) on upper handle. You will hear a “snap” when the trigger rod is in place. A C D B Replace clean solution tank (upper tank) by positioning bottom first. Press on tank handle to snap top of tank into place. Place nuts in recessed areas on back of hose holder. Hold each nut in place while tightening each bolt securely (from the front of the handle) with a Phillips screwdriver. Only two nuts are needed on this model. The extra nut is not required but has been provided for your convenience. Attach tool holder Remove tool and taped screw from holder. Insert projections on holder into slots on back of cleaner. Slide holder down into place. Insert screw at (E) and tighten with a Phillips screwdriver. E 1-14 1-10 1-11 Storing hose & tool Stretch hose out and identify ends. F. Nozzle connector end of hose H. Solution tube G. Trigger I. Converter end of hose Note: You may find it helpful when storing the hose and nozzle to refer to the informa- tion on the back of the deep cleaner and on the converter end of the hose. Start with converter end of hose (I). Fit converter over tab near tool holder (j). Press converter firmly to snap in place. Press solution tube (H) into clip next to converter as shown. H I IJ K L H L G F 1-12 1-13 1-14 1-10 1-11 Storing hose & tool Stretch hose out and identify ends. F. Nozzle connector end of hose H. Solution tube G. Trigger I. Converter end of hose Note: You may find it helpful when storing the hose and nozzle to refer to the informa- tion on the back of the deep cleaner and on the converter end of the hose. Start with converter end of hose (I). Fit converter over tab near tool holder (j). Press converter firmly to snap in place. Press solution tube (H) into clip next to converter as shown. H I IJ K L H L G F 1-12 1-13 Wrap hose around hook on upper Wrap hose around lower tool holder and Press cord into cord clip on back of handle (K). Press hose into clips on continue until nozzle connector is near hose holder. Pull cord tight. upper hose holder (L). upper hose holder. Clip hose in place. 1-15 Position stair/upholstery nozzle (models with powered hand tool) or utility nozzle (not included with all models) in holder at base of cleaner and snap it into place as shown at arrow. 1-16 Slide bare floor attachment into holder as shown. (Not included with all models.) ContinuedO Upfront tool storage 1-17 M N On some models, a powered hand tool stores behind the door on front of the handle (M). On other models, the stair/upholstery nozzle stores in this area (N). O 1-20 To replace tool, push connector end of tool (O) up into opening in storage area. Snap nozzle into place. 1-18 Powered hand tool The powered hand tool is shipped in a plastic bag for protection. To remove the bag before using the tool, open tool door. Stair/upholstery nozzle To store stair/upholstery nozzle, open tool door, place nozzle in bracket and fit it securely into position. To remove, reverse this procedure. For models with the powered hand tool, the stair/upholstery nozzle stores on the back of the cleaner (Fig. 1-15). 1-19 Pull tool down and outward. Remove tool from bag. Discard bag. 1-22 How to reattach tool cover The tool cover is designed with a breakaway feature which allows it to snap free if it is pushed open too far. To reattach, align hinges of cover with slots on sides of tool storage area. Push cover down to secure in place. 2. How to use Deep cleaner description The assembled deep cleaner will look like the drawing. 2-1 16 24 18 19 1 32 5 9 10 11 12 13 14 15 17 21 20 23 2-2 A B ON/OFF pedal & Handle release pedal Step on pedal (A) to turn deep cleaner on. Step on pedal again to turn deep cleaner off. Step on pedal (B) to lower handle to operating position. Handle does not lock into a single position but “floats” to allow convenient operation. 1. Hand grip 2. Solution trigger: press to release clean solution. 3. Clean Surge™ button 4. Cord clip: place cord in clip to keep it out of the way when using cleaner 5. Hose 6. Hose holder: wrap hose around holder and hooks for storage. 7. Hose hooks 8. Cord hooks: wrap cord around hooks for storage. The top hook can be rotated right or left for quick and easy cord release. 9. Powered hand tool or stair/ upholstery nozzle 10. Carrying handle 11. Clean solution tank handle 12. Clean solution tank cap/ measuring cup 13. Clean solution tank: holds cleaning solution. 14. Recovery tank lid 15. Recovery tank: holds dirty solution. 4 5 7 7 6 8 8 25 22 26 2-3 To transport To move your deep cleaner from room to room put handle in upright and locked position tilt deep cleaner back on wheels and push forward. 16. Recovery tank front panel 17. Hood 18. Brush speed selector: slide selector to set brush speed on HI, LO, or OFF. 19. B...
Эта инструкция также подходит к моделям:Пылесосы - SteamVac F5903-900 (508.15 kb)