Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Fill the flask with water and use the funnel to pour it into the tank. Keep the water level under the “MAX” fill line. (fig. 3) 3 Replace the water tank cap and turn it clockwise to the locked position. S3250W_11-S3250W3_11_IB_ENG_100930.indd 5 10-09-30 10:28 AM Using Your Light & Easy™ Steam Mop When you use your steam mop for the first time or if you have not used the unit in awhile, it may take a minute or two for the water to travel through the pump and into the heater to create steam. Get it started by pumping the handle a few times. If you have waited a few minutes and you still do not see any steam, reference the troubleshooting section on page 11. fig. 1 fig. 2 fig. 3 IMPORTANT: Your steam mop needs water to make steam! Never use your steam mop without water in the tank. Sweep or vacuum your floors prior to cleaning with your Light & Easy™ Steam Mop. Visit for other great quick cleaning products to complement your Light & Easy™ Steam Mop, such as the Shark® SV800 Cordless Stick Vac. 1 Pull and twist the quick release cord holder to unwrap the power cord completely. (fig. 1) Plug into a 120-volt electrical outlet. (fig. 2) The “On” light will turn blue. If the light does not turn on, reference the troubleshooting section on page 11. (fig. 3) S3250W_11-S3250W3_11_IB_ENG_100930.indd 6 10-09-30 10:28 AM fig. 4 fig. 5 If your Light & Easy™ Steam Mop stops steaming, it could be out of water. Unplug the power cord from the electrical outlet and refill the water tank at anytime. If your Light & Easy™ Steam Mop stops steaming, it could be out of water. Unplug the power cord from the electrical outlet and refill the water tank at anytime. 2 Wait 30 seconds for the boiler to 3 Mop with a forward and backward heat the water. Pump the handle motion to customize steam output a few times to prime the pump, automatically. (fig. 5) activate steam and moisten the micro-fiber pad. (fig. 4) S3250W_11-S3250W3_11_IB_ENG_100930.indd 7 10-09-30 10:28 AM Using Your Light & Easy™ Steam Mop 1 Clean under furniture and tight areas using the Shark® Backsaver™ locking handle. Press the handle release button and apply slight pressure to bend the handle. The Shark® Backsaver™ joint will lock at a perfect, access-maximizing angle. (fig. 1) 2 Press the release button on the handle again to straighten. fig. 1 S3250W_11-S3250W3_11_IB_ENG_100930.indd 8 10-09-30 10:28 AM English Care of Your Light & Easy™ Steam Mop fig.2 fig.3 fig. 1 AFTER USE AND STORAGE 1 When you have finished using the Light & Easy™ Steam Mop, unplug the cord from the outlet and place the mop into the upright position (fig. 1) and let the unit cool 2-3 minutes. Release steam by pumping the handle several times. 2 Carefully separate micro-fiber cleaning pad from steam mop, avoiding contact with the hot pocket or dirt. (fig. 2) 3 Empty the water tank before storage. Remove the water tank cap and empty the tank over a sink. Replace the water cap. 4 To store the cooled Shark® Light & Easy™ Steam Mop, hang on a large hook. (fig. 3) NOTE: If you want to store the Light & Easy™ Steam Mop standing upright, make sure it is leaning against a wall for added support and safety. Always store your Shark® Light & Easy™ Steam Mop with the micro-fiber cleaning pad removed. Store away from children and high traffic areas. S3250W_11-S3250W3_11_IB_ENG_100930.indd 9 10-09-30 10:28 AM Care of Your Light & Easy™ Steam Mop fig. 5 fig. 6 CARE OF YOUR MICRO-FIBER CLEANING PAD 1 Wash pads in warm water. Wash separately from other laundry. Only use liquid detergent (no powder detergent). Do not use fabric softeners. Line dry or dry on a low dryer setting. (fig. 5) 2 If there are loose threads on the pad carefully cut the threads with scissors. Do not pull on them or cut at the base. (fig. 6) IMPORTANT: The micro-fiber cleaning pad may be very hot from the steam. Use caution when removing. Let the unit cool for 2-3 minutes. ORDERING REPLACEMENT PARTS To order additional parts and accessories, feel free to contact us at or call 1-800-798-7398. NOTE: Some parts may be available at your local retailer. Contact customer service for any other servicing. S3250W_11-S3250W3_11_IB_ENG_100930.indd 10 10-09-30 10:28 AM English Trouble Shooting PROBLEM POSSIBLE REASONS & SOLUTIONS The Light & Easy™ Steam Mop will not turn-on. Your steam-mop should be securely plugged into a 120V AC electrical outlet only. Check your fuse or breaker. If your unit still does not work, call 1-800-798-7398. Light & Easy™ Steam Mop will not make steam. Is there water in the water tank? If not, add water to your Steam Mop following instructions on page 5. Light & Easy™ Steam Mop leaves water on the floor. Is your micro-fiber cleaning pad too wet? Unplug your Steam Mop and change the micro-fiber cleaning pad. Light & Easy™ Steam Mop left white spot on the floor. Do not leave your steam-mop on the floor with a damp or wet cleaning pad. Do you have hard water? If you do, you might want to switc...