Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Chemicals or cleaning solutions may be unsafe or cause damage. IMPORTANT: Please wait 3-5 minutes for your Light & Easy™ Steam Mop to cool off before removing the micro- fiber pad. Getting Started Replacement micro-fiber pads are available at or by calling 1-800-798-7398. Your micro-fiber cleaning pads should be replaced every 3 months to maximize cleaning performance. fig. 1 4 TOLL FREE: 1 800 798 7398 ATTACHING THE MICRO-FIBER PAD 1 Place the micro-fiber cleaning pad on the floor with the quick fastener strips facing up. Place the Light & Easy™ Steam Mop on the top of the pad to attach. (fig. 1) IMPORTANT: Only add water to the tank. Chemicals or cleaning solutions may be unsafe or cause damage. IMPORTANT: Please wait 3-5 minutes for your Light & Easy™ Steam Mop to cool off before removing the micro- fiber pad. Getting Started Replacement micro-fiber pads are available at or by calling 1-800-798-7398. Your micro-fiber cleaning pads should be replaced every 3 months to maximize cleaning performance. fig. 1 S3251_11_ENG_IB_101117.indd 4 10-11-17 1:58 PM Calcium and mineral deposits can build up and impact the performance of your steam mop over time. To extend the life of fig. 3 fig. 2 your product we recommend that you use distilled water or Shark®’s Water Filtration Bottle. Visit sharkclean.com to order. FILLING THE WATER TANK IMPORTANT: Unplug the Light & Easy™ Steam Mop before filling the water tank with water. (fig. 2) Remove the water tank cap by turning it counter-clockwise to the unlocked position. (fig. 3) 2 A filling flask and funnel are included with your Light & Easy™ Steam Mop to make filling the water tank easy. Fill the flask with water and use the funnel to pour it into the tank. Keep the water level under the MAX’ fill line. 3 Replace the water tank cap and turn it clockwise to the locked position. S3251_11_ENG_IB_101117.indd 5 10-11-17 1:58 PM Using Your Light & Easy™ Steam Mop When you use your steam mop for the first time or if you have not used the unit in awhile, it may take a minute or two for the water to travel through the pump and into the heater to create steam. Get it started by pumping the handle a few times. If you have waited a few minutes and you still do not see any steam, reference the troubleshooting section on page 10. fig. 1 fig. 2 fig. 3 IMPORTANT: Your steam mop needs water to make steam! Never use your steam mop without water in the tank. Sweep or vacuum your floors prior to cleaning with your Light & Easy™ Steam Mop. Visit for other great quick cleaning products to complement your Light & Easy™ Steam Mop, such as the Shark® Navigator. 1 Pull and twist the quick release cord holder to unwrap the power cord completely. (fig. 1) Plug into a 120-volt electrical outlet. (fig. 2) The “On” light will turn blue. If the light does not turn on, reference the troubleshooting section on page 10. (fig. 3) S3251_11_ENG_IB_101117.indd 6 10-11-17 1:58 PM at anytime. fig. 4 fig. 5 at anytime. fig. 4 fig. 5 2Wait 30 seconds for the boiler to heat the water. Pump the handle a few times to prime the pump, activate steam and moisten the micro-fiber pad. (fig. 4) If your Light & Easy™ Steam Mop stops steaming, it could be out of water. Unplug the power cord from the electrical outlet and refill the water tank 3 Mop with a forward and backward motion to customize steam output automatically. (fig. 5) IMPORTANT: Never leave the Light & Easy™ Steam Mop with a damp/wet micro-fiber pad on any floor surface for any amount of time as this may damage the floor. S3251_11_ENG_IB_101117.indd 7 10-11-17 1:58 PM Care of Your Light & Easy™ Steam Mop fig. 1 fig.2 AFTER USE AND STORAGE 1 When you have finished using the Light & Easy™ Steam Mop, unplug the cord from the outlet and place the mop into the upright position (fig. 1) and let the unit cool 3-5 minutes. Release steam by pumping the handle several times. 2 Carefully separate micro-fiber cleaning pad from steam mop, avoiding contact with the hot pad or dirt. (fig. 2) 3 Empty the water tank before storage. Remove the water tank cap and empty the tank over a sink. Replace the water cap. fig.3 4 To store the cooled Shark® Light & Easy™ Steam Mop, hang on a large hook. (fig. 3) NOTE: If you want to store the Light & Easy™ Steam Mop standing upright, make sure it is leaning against a wall for added support and safety. Always store your Shark® Light & Easy™ Steam Mop with the micro-fiber cleaning pad removed. Store away from children and high traffic areas. S3251_11_ENG_IB_101117.indd 8 10-11-17 1:58 PM English Care of Your Light & Easy™ Steam Mop fig. 4 fig. 5 CARE OF YOUR MICRO-FIBER CLEANING PAD 1 Wash pads in warm water. Wash separately from other laundry. Only use liquid detergent (no powder detergent). Do not use fabric softeners. Line dry or dry on a low dryer setting. (fig. 4) 2 If there are loose threads on the pad carefully cut the threads with scissors. Do not pull on them or cut at ...