Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
Once you adjust the rear speaker output level for each surround mode, the adjusted level is stored in memory. • You cannot adjust the right and left rear speaker levels separately. On the remote control ONLY: SHIFT 1Press and hold SHIFT. 2Press REAR LEVEL – / + button. – REAR LEVEL • Pressing REAR LEVEL – decreases the + output level (from +10 to –10). • Pressing REAR LEVEL + increases the output level (from –10 to +10). 3Release SHIFT. Creating Your Own Sound Mode — Manual Mode You can change SEA pattern to suit your preference. These changed settings can be stored in the MANUAL 1, 2, and 3 modes. • There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again. • If you want to add the surround elements in your SEA pattern, select one of the surround modes (D.CLUB, HALL, or STADIUM) before starting the procedure below. On the unit ONLY: SEA CONTROL 1Press and hold SEA CONTROL until “SEA CONT” appears on the display. SET PRESET 2Adjust the SEA pattern. 1) Press 4or .to select the frequency range to adjust (LOW, MID, HIGH). TUNING 2) Press 1or Ato adjust the level (–3 to +3) of the selected frequency range. 3) Repeat steps 1) and 2) to adjust the level of the other frequency ranges. SEA CONTROL 3Press SEA CONTROL again. SET 4Press 4or .to select one of the MANUAL 1, 2, and 3 modes into which you want to store the SEA pattern. SEA CONTROL 5Press SEA CONTROL again. SET The SOUND MODE indicator also lights up. The SEA pattern you have created are stored into the MANUAL mode selected in the above step. To use your own sound mode Select MANUAL 1, 2, or 3 mode when using the sound modes. See “Selecting the Sound Modes” on page 11. If you have stored your MANUAL 1, 2, and 3 modes with the surround elements You can also adjust the rear speaker output level. See “While using one of the surround modes”. Current level appears. – 12 – EnglishEnglish Listening to FM and AM (MW/LW) Broadcasts AM FM Tuning in a Station On the unit ONLY: 1Press FM/AM. The unit automatically turns on and tunes in the previously tuned station (either FM or AM — MW/LW). The Powered Rolling Panel automatically opens. FM AM/ • Each time you press the button, the band alternates between FM and AM (MW/LW). TUNING 2Press and hold TUNING – / + for more than 1 second. The unit starts searching for stations and stops when a station of sufficient signal strength is tuned in. If a program is broadcast in stereo, the STEREO indicator lights up. To stop during searching, press TUNING – / +. When you press TUNING – / + briefly and repeatedly The frequency changes step by step. To change the FM reception mode FM MODE When an FM stereo broadcast is hard to receive or noisy, press FM MODE on the remote control so that the MONO indicator lights up on the display. Reception improves. To restore the stereo effect, press FM MODE again so that the MONO indicator goes off. In this stereo mode, you can hear stereo sounds when a program is broadcast in stereo. Presetting Stations You can preset 30 FM and 15 AM (MW/LW) stations. In some cases, test frequencies have been already memorized for the tuner since the factory examined the tuner preset function before shipment. This is not a malfunction. You can preset the stations you want into memory by following the presetting method. • There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again. 1Tune in the station you want to preset. • See “Tuning in a Station” above. MHz SEA CONTROL 2Press SET. SET PRESET 3Press PRESET – / + to select a preset number. SEA CONTROL 4Press SET again. SET The tuned station in step 1 is stored in the preset number selected in step 3. • Storing a new station on a used number erases the previously stored one. When you unplug the AC power cord or if a power failure occurs The preset stations will be erased in a few days. If this happens, preset the stations again. Tuning in a Preset Station 1Press FM/AM. The unit automatically turns on and tunes in the previously tuned station (either FM or AM — MW/LW). The Powered Rolling Panel automatically opens. FM AM/ • Each time you press the button, the band alternates between FM and AM (MW/LW). PRESET 2Select a preset number. On the unit: Press PRESET – / +. On the remote control: PRO LOGIC 3 STEREO TEST TONE Press the number buttons. CENTER CENTER MODE For preset number 5, press 5. –+ LEVEL For preset number 15, press +10, then 5. – REAR + DELAY TIME LEVEL For preset number 20, press +10, L BALANCE R then 10. For preset number 25, press +10, +10, then 5. – 13 – Continued Receiving FM Stations with RDS English RDS allows FM stations to send an additional signal along with their regular program signals. For example, the stations send their station names, as well as information about what type of program they broadcast, such as sports or music, etc. When tuned to an FM station which provides the RDS service, the RDS indicator lights u...