Оценок - 3, средний балл: 3
(
)
)
|
Фрагмент инструкции
4. With your device on, press ON•OFF. If the device turns off, no further programming is required. Note: If some buttons do not operate your equipment, try one of the other codes for your brand. Write your codes down here for easy reference later. Device Device stored Code TV TV VCR CBL/SAT DVD/AUX 7 CodeSearch If your device does not respond after you have tried all the codes for your brand, or if your brand is not listed, try searching for your code by following these steps. 1. Manually turn on the device (TV, VCR, etc.) to be controlled. 2. Press and hold the CODE SEARCH button until the red indicator stays on, then release the CODE SEARCH button. 3. Press and quickly release the desired device button (TV, VCR, etc.). The red indicator blinks off once. 4. Press the ON•OFF button repeatedly (up to 300 times) until the device to be controlled turns off. The red indicator blinks off with each button press. . Press and release ENTER to install the code. Most users will store VCR codes under the VCR button, Cable codes under CABLE, etc. If (for example) you want to store a VCR code under DVD/AUX, first follow the procedure for Direct Code Entry (previous page) and press DVD/AUX in step 2 of Direct Code Entry, then enter ANY VCR code in step 3 of Direct Code Entry. Then follow the steps above for Code Search. Note: Code Search starts from the currently stored 4 digit number under that mode. Sometimes the first code that “works” with your device may only allow limited functionality (e.g. the MENU button might not work). There may be a code that performs more functions. Continue the code search process until the best code is found. 8 UsingYourRemote Code Identification The Code Identification Feature allows you to identify the 4 digit library code stored under your device button. For example, if you want to find out what 4 digit code is stored under your TV device button, follow the six steps below: 1. Press and hold the CODE SEARCH button until the red indicator stays on. Release the CODE SEARCH button. 2. Press and release the desired device button (TV, VCR, etc.). The red indicator blinks, then stays lit. 3. Press and release the CODE SEARCH button. The red indicator blinks once and remains lit. 4. To find the first digit for the code stored under the device button pressed in step 2, press each numeric button from 0-9 in turn. The number that causes the indicator light to blink is the first digit in your code. 5. To find the second digit, repeat step 4, this time when the red indicator blinks off this is the second digit. 6. Repeat step 4 to find the third and fourth digits. 9 UsingYourRemote,cont. Sleep Function The Sleep button enables the remote to turn off your TV after a period of 1 to 99 minutes as shown below. The remote must be in TV mode to set a Sleep Timer. This feature works even if your TV does not have a sleep feature. 1. Press and release the TV device button. 2. Press and hold the Sleep button until the LED remains lit (about 2-3 sec- onds). 3. Release the Sleep button. 4. Press and release the numeric buttons (01-99) for the time required. The LED will blink off to indicate button press acceptance. . TV Sleep Timer is set. 6. Leave the Remote pointing towards the TV with an unobstructed path. To cancel the Sleep Timer, press and hold the Sleep button until the LED blinks, or press and release the Power button in TV mode. 10 UsingYourRemote,cont. Controlling Devices with Separate Power On and Off Buttons Some GE, RCA and ProScan models require you to press the device button for more than one second to turn the device on and the ON•OFF button to turn the device off. Controlling Combo Devices Some Combo devices (e.g. TV/VCR, TV/DVD, DVD/VCR, etc.) will require you to set up two different Mode buttons to control both parts of the Combo device. For example, if you have a TV/ DVD Combo, you might need to set up one code under the TV button to control the TV part AND a separate code (under any other Mode button) to control the DVD part. VCR/DVD Punch-Through This remote allows the 6 VCR transport buttons (i.e. PLAY, PAUSE, STOP, FF, REWIND, and REC) to Punch-Through control from any Mode programmed with TV, SAT or Cable codes to the last VCR, or DVD programmed Mode you used. This feature will not operate if the programmed TV, SAT or Cable code has its own VCR transport button control e.g. a TV Combo, SAT/PVR, etc. 11 UsingYourRemote,cont. Volume/Mute Control and Punch- Through This remote lets you select which device Mode controls your Volume/Mute buttons. The remote is initially set for all device Modes to use their own Volume/Mute control if present. If the programmed code has no Volume/Mute operation of its own then those buttons will punch-through control to the TV Mode device without needing to change to TV Mode. Any Mode chosen for Volume/Mute control MUST have its own Volume/Mute function or the Volume/Mute buttons will do nothing. Setting ALL Volume/Mute Control to any one Mode This routine ...