Войти:
Оценок - 3, средний балл: 3.7 ( )

Инструкция по эксплуатации AMX, модель Mio Modero DMS (FG2408-01XX)

Производитель: AMX
Размер: 179.94 kb
Название файла: MIO-DMS.Metallic.QuickStartGuide.pdf
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


Menu Up Menu items Menu select pushbuttons Menu Down FIG. 1 Mio Modero DMS Device Family Specifications Mio Modero DMS (FG2408-01XX) Specifications Power 12 VDC / PoE: Maximum power consumption (PoE): • 5.5 Watts Maximum startup (rush) current (PoE): • 150 mA @ 50 VDC Maximum continuous current (PoE): • 100 mA @ 50 VDC Maximum power consumption (DC): • 5.0 Watts Maximum startup (rush) current (DC): • 525 mA @ 13.5 VDC Maximum continuous current (DC): • 350 mA @ 13.5 VDC Front Panel Components: • LCD display • 8 pushbuttons Rear Panel Connectors: • Ethernet Port (PoE) • 2-pin 3.5 mm mini-Phoenix (female) connector • 4 Magnetic Posts • Ground wire Dimensions (HWD): (inside of conduit box) • 6.25 (158.8 mm) x 3.50 (91.4 mm) x 3.93 (99.7 mm) Supported Fonts: Only True Type Fonts Weight (range): • Device - .55 lbs (.25 kg) Operating Environment: • Operating Temperature: 0° to 40° C (32° to 104° F) • Storage Temperature: -10° to 60° C (14° to 140° F) Mounting: The Mio Modero DMS is installed in one of three ways: • Rough-in mounting • Expansion clips for pressure mounting • No tabs for brick and mortar mounting Available Color Schemes: Gold (GL), Silver (SL) Included Accessories: • 2-pin 3.5 mm mini-Phoenix connector (41-5025) • Conduit box (FG039-11) • Mounting kit (KA2250-01) Other AMX Equipment: • NXA-ENET24PoE: Managed Ethernet Switch, Power Over Ethernet (FG2178-61) Dynamic Menu System Using the KeypadBuilder application available for download from the Mio Modero DMS is programmed with a Dynamic Menu System (DMS) that is navigated via the 8 pushbuttons and LCD display area. See the KeypadBuilder Instruction Manual for more information on programming Mio Modero DMS devices. Installation Note: To avoid any damage to the electronic component, installation must be performed in an ESD safe environment. The device and conduit box must have an Earth ground. The installation section addresses the mounting and wiring of the Mio Modero DMS. After you have completed the installation you must consult Necessary Device Setup. Rear Components The rear components of the Mio Modero DMS (FIG. 2) are as follows: Ethernet Port (PoE) FIG. 2 Mio Modero DMS Rear Components 2-pin 3.5 mm (female) connector mini-Phoenix (Front View) Magnetic Posts Connections and Wiring The Mio Modero DMS device is powered either via 12VDC or Power over Ethernet (PoE). If both the 12 VDC and PoE power sources are connected, by default the device draws power from the 12 VDC. If the 12 VDC source is disconnected, the PoE automatically supplies power after a device reboot. Note: Do not connect power to the Mio Modero DMS until the wiring is complete. Preparing captive wires for the 2-pin 3.5 mm mini-Phoenix connector You will need a wire stripper, and flat-blade screwdriver to prepare and connect the captive wires. 1. Strip 0.25 inch (6.35 mm) of wire insulation off all wires. 2. Insert each wire into the appropriate opening on the connector according to the wiring diagrams and connector types described in this section. 3. Turn the screws clockwise to secure the wires in the connector. Note: Do not over-torque the screws; doing so can bend the seating pins and damage the connector. Using the PSN NetLinx connector for power The PWR and GND wires from the 12 VDC power supply must be connected to the corresponding location on the 2-pin 3.5 mm mini-Phoenix connector (See the KeypadBuilder Instruction Manual for an illustration). 1. Insert the PWR and GND wires on the terminal end of a PSN 2-pin 3.5 mm mini- Phoenix cable. Match the wiring locations of the +/- on both the power supply and the terminal connector. 2. Tighten the clamp to secure the two wires. 3. Verify the connection of the 2-pin 3.5 mm mini-Phoenix to the power supply. Using the Ethernet port for power (PoE) Connect your CAT5/CAT6 Ethernet cable to the port shown in FIG. 2. (See the Mio Modero DMS & Mio Modero DMS Pinnacle instruction manual for an illustration and cable pinouts). Mounting Procedures Consult the Mio DMS & Mio DMS Pinnacle instruction manual for setting a Host FIG. 3 shows the mounting dimensions for the Mio Modero DMS. Reference these Name. measurements when planning and installing the device. Consult the Mio Modero Mio DMS Menu Navigation DMS & Mio Modero DMS Pinnacle instruction manual for the rough-in and no tab Follow these tips to set your device information: installation methods. • The Up and Down buttons scroll through numerals, upper case and lower case letters. Expansion Clip Installation It is recommended that you cutout the surface slightly smaller than what is outlined in the installation drawings so that you can make any necessary cutout adjustments. Before you begin, if you are using the 2-pin power connector, verify that the terminal end of the power cable is not connected to a power source. 1. If assembled, pull the Mio Modero DMS from the conduit box. 2. Cut out the surface for the Mio Modero DMS conduit box using the dimensions shown in FIG. 3. ...


Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории