Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Flip and turn the Mio R-1 device so that the buttons are facing away from you and the device is upside down. 2. Holding the device in both hands, place your thumbs on the battery door and push up to slide the battery door free. 3. Unscrew the 6 screw points indicated in FIG. 2. 6 Screw Points Programming Jack FIG. 2 Internal Mio R-1 Components 4. Turn the unit over so the buttons are facing you. 5. Lift the top assembly away from the PCB. 6. If necessary, push out the standard buttons from the front of the top assembly. 7. Drop on your custom button pad and verify the alignment with the guide posts on the PCB. 8. Place the top assembly back down on the PCB and return the unit over, exposing the 6 screw points. 9. Tighten the 6 screw points. 10. Place the battery door back on the device, slide to lock it in place. Inserting Batteries into The Mio R-1 To install your 4 AAA batteries into the Mio R-1 device: 1. Flip and turn the Mio R-1 device so that the buttons are facing away from you and the device is upside down. 2. Holding the device in both hands, place your thumbs on the battery door and slide the battery door free. 3. Insert the batteries as indicated inside the battery compartment. 4. Place the battery door back on the device, slide to lock it in place. Battery Low Indicator When the battery charge level is too low to sustain continuous operation, the LCD flashes, "Battery Low" and the device shuts down. Programming The Mio R-1 Using KeypadBuilder Most functionality of the Mio R-1 is handled using the application, KeypadBuilder. Go to for the KeypadBuilder Instruction Manual. There are a select number of Serial Commands the Mio R-1 recognizes. For a full list and descriptions, consult the Mio R-1 Instruction Manual on Using Connector Ports on The Mio R-1 The programming jack is used for communication between the device and KeypadBuilder. The programming jack uses a three-wire, 2.5 mm stereo jack, you can order the programming cable (FG10-817) from AMX if you do not currently possess one. While loading your configuration file make sure the device is situated as such that the batteries will not fall out. The load will fail if your batteries fall out during the process. The Mio communicates at 115200 baud rate. To download KeypadBuilder Configuration Files: 1. Set the Mio R-1 Download mode to ON. See the Configuration Mode section for details. 2. Flip and turn the Mio R-1 device so that the buttons are facing away from you and the device is upside down. 3. Holding the device in both hands, place your thumbs on the battery door and slide the battery door free. 4. Connect the 2.5 mm stereo plug (male) end of the programming cable (FG10817) into the programming jack on the bottom side of the remote device. 5. If necessary, connect the DB-9 end of the programming cable to the female DB-9 connector on the DB-9 extension cable (FG10-727). 6. Connect the female DB-9 terminal end of the extension cable to the port on the back of your computer. 7. Configure the communication parameters in KeypadBuilder. FIG. 3 Connecting The Keypad Device to Your PC Stereo plug male DB-9 connector Cable FG10-817 to cable FG10-727 to PC programming cable Keypad device Programming jack Mio R-1 IR Code Matrix The IR Code emitted depends upon which of the 6 configurable modes is selected. Below is the list of codes for each button within each mode. IR Code Matrix Button Label Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 Mode 6 1 Power Symbol 9 49 89 129 169 209 2 GUIDE 38 78 118 158 198 238 3 EXIT 37 77 117 157 197 237 4 MENU 31 71 111 151 191 231 5 INFO 39 79 119 159 199 239 6 L 32 72 112 152 192 232 7 M 33 73 113 153 193 233 8 K 34 74 114 154 194 234 9 A 35 75 115 155 195 235 10 SELECT 36 76 116 156 196 236 11 VOL + 24 64 104 144 184 224 12 VOL 25 65 105 145 185 225 13 CH + 22 62 102 142 182 222 14 CH 23 63 103 143 183 223 15 LAST 40 80 120 160 200 240 16 MUTE 26 66 106 146 186 226 17 1 11 51 91 131 171 211 18 2 12 52 92 132 172 212 19 3 13 53 93 133 173 213 20 4 14 54 94 134 174 214 21 5 15 55 95 135 175 215 22 6 16 56 96 136 176 216 23 7 17 57 97 137 177 217 24 8 18 58 98 138 178 218 25 9 19 59 99 139 179 219 26 INPUT 29 69 109 149 189 229 27 0 10 50 90 130 170 210 IR Code Matrix (Cont.) Button Label Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 Mode 6 28 ENTER 21 61 101 141 181 221 29 A (Macro 1) 250 250 250 250 250 250 30 B (Macro 2) 251 251 251 251 251 251 31 C (Macro 3) 252 252 252 252 252 252 32 TV (Mode 1) 241 241 241 241 241 241 33 SAT (Mode 2) 242 242 242 242 242 242 34 DVD (Mode 3) 243 243 243 243 243 243 35 CD (Mode 4) 244 244 244 244 244 244 36 AUX (Mode 5) 245 245 245 245 245 245 37 LGHT (Mode 6) 246 246 246 246 246 246 38 STOP B 2 42 82 122 162 202 39 REC J 8 48 88 128 168 208 40 PAUSE C 3 43 83 123 163 203 41 S. REV Z 7 47 87 127 167 207 42 PLAY A 1 41 81 121 161 201 43 S. FWD Y 6 46 86 126 166 206 44 REW E 5 45 85 125 165 205 45 FWD D 4 44 84 124 164 204 Configuration Mode The configuration mode allows you to ...