Производитель: Philips
Размер: 750.27 kb
Название файла:
|
Фрагмент инструкции
2 Press and release keys 1 and 6 simultaneously. Important: after pressing the keys, you have to release them immediately! – The green LED lights up. 3 Press the two digits key. – The green LED goes out. 4 Press key 1 and count the number of times the green LED flashes. This is the first digit of the 3-digit code. (No flashes means the digit is zero.) 5 Press key 2 and count the number of flashes for the second digit. 6 Press key 3 and count the number of flashes for the third digit. 7 Note the code. PROG 1 6 TV VCR SAT AUDIO 1 2 3 Instructions for use Instructions for use English English 1 9 9 2 1 6 TV VCR SAT AUDIO TV VCR SAT AUDIO ADVANCED TIPS AND TRICKS A DVICE Carefully read the complete procedure before starting! Changing the device keys With the mode selector it is possible to select 4 categories of devices you want to operate. Each category (TV, VCR, SAT and AUDIO) is meant to operate a specific group of equipment: TV VCR SAT AUDIO tv vcr sat CD laserdisc cable dvd Once you have programmed the functions of a device in one of the categories, it is not possible to program another device in the same category. There is, however, a solution in case you want to program two devices in the same category (2 TV’s, VCR’s, etc.). The following example explains how. EXAMPLE: The SAT mode on this remote control is factory preset to control many Philips satellite receivers. You can change the SAT mode (or any mode) to operate another type of device. The following example shows you how to use the SAT mode to operate a second TV: 1 Press the mode selector key to select SAT and make sure the second TV is switched on. 2 Press and hold keys 1 and 6 simultaneously - for about 3 seconds - until the green LED lights up. 3 On the keypad, press keys 9, 9 and 2. 4 Press the mode selector key to select TV mode. 5 Press key 1. – The LED flashes twice to indicate successful set up. That’s it! Don’t forget to set up the SBC RU640 to operate this second TV. See the section Set-up for use. 1 6 TV VCR SAT AUDIO 9 9 TV VCR SAT AUDIO 1 9 Punch-Through Sound Punch-through sound enables you to control the audio level of your first or second TV, regardless of what device mode the remote control is in. EXAMPLE: You have installed a second TV under SAT mode. You can control that TV’s volume when you are in VCR mode. This feature is installed as a default setting for a first TV. To install this feature for a second TV: 1 Press the mode selector key to select VCR. 2 Press and hold keys 1 and 6 simultaneously -for about 3 seconds - until the green LED lights up. 3 3 On the keypad, press keys 9, 9, and 3. 4 Press the mode selector key to select SAT (second TV). 5 Press the power key. – That’s it! The LED flashes twice to indicate successful set up. The Volume up/down keys now control the volume of your second (SAT) TV when you’re in VCR mode. Functional back-lighting When you pick up the SBC RU640 and tilt it over about 60 degrees, the main keys for the device you want to operate are automatically back-lit. In VCR mode for example, only the main keys that are needed to operate the VCR are back-lit. You can choose to have all of the keys back-lit, or you can switch off the functional back-lighting feature completely. To back-light all of the keys: • Press keys 1 and 9 simultaneously - for about 3 seconds until the green LED flashes twice. – The functional back-lighting is now de-activated and all keys light up when you pick up the remote control. Pressing keys 1 and 9 simultaneously again - for about 3 seconds - will return the back-lighting to its preset functional setting. N OTE The back-lighting turns off if you don’t move the remote control or if you don’t press a key within 4 seconds. 6 7 Instructions for use Instructions for use English TIP The automatic back-lighting provides you with unparalleled ease of use, even in the most dimly-lit of rooms. While the remote control is actively being moved about the backlighting stays on. This consumes more power than normal and may require you to change your batteries more frequently. You can easily turn the back-lighting function off to conserve power. To do this please follow the instructions below. To remove the back-lighting completely: 9 • Press keys 7 and 9 simultaneously - for about 3 seconds until the green LED flashes twice. – The back-lighting is now de-activated. Pressing keys 7 and 9 simultaneously again - for about 3 seconds -will return the back-lighting to its preset functional setting. Programming macros A macro is a short-cut to performing a series of functions, simply by pressing one key. You can program your own macros: 6 9 1 1 Press and hold the key 1 and the 6 at the same time - for about 3 seconds - until the green LED lights up. 2 Press keys 9, 9 and 1. 3 Press the key you want to program the macro under. You can now enter all the keys (up to 8) that you want the SBC RU640 to transmit. For detailed information see the subtitle example below. SHIFT 4 Press the Shift key for ...
Эта инструкция также подходит к моделям:Пульт ду - SBCRU640/87 (750.27 kb)