Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
l. If learning the first or second buttons for a Mode results in continuous errors then try the following: i. End the Learn session by pressing the SETUP key. ii. Clear out the learned commands for that Mode. iii. Check the IR transmitters are correctly aligned between the two remotes (use the IR Transmitter Finder facility). iv. Adjust the distance between the two remotes to be closer (e.g. half an inch) or a further away (e.g. 2 inches) from each other. v. Try learning the original remote for that Mode again. If problems reoccur with the same button check the original remote button being learned – does it transmit? Does it operate the target device? Try learning that button under a different clear Mode. If it learns okay then it is likely to be a different code type from the others and cannot be learned under the same Mode. 14 15 Learning CommandsIR Transmitter Finder Feature This feature assists you in identifying where your original remotes IR transmitter is located and is particularly useful if your original remote’s IR transmitter is hidden behind a lens. 1. Point both remotes facing each other by approximately 1 inch apart (see Tips on Learning on previous pages) 2. Press and hold the SETUP button until the red indicator turns on, then release the button. 3. Press and release the desired Mode button (TV, VCR, etc.), the red indicator blinks then stays on. 4. Press and release the LEARN button, the red indicator blinks then stays on. 5. Press and hold any Original Remote button and move the Original Remote to the left and right, and/ or, up and down in front of the Learning remote IR transmitter. The red indicator will remain on if no IR from the Original remote is found and the red indicator will blink on and off more rapidly when the IR transmitters are lining up. The point where the red indicator blinks most rapidly is where the two IR transmitters are aligned. Note some original remotes will only transmit IR on the initial button press then stop. In these cases, quickly press and release the original remote button repeatedly during this procedure. 6. You can now learn a button from your original remote by continuing from “Step 4” in the “Learning Commands” section on the next page, or, to exit at this point, press and release the SETUP button The learning feature allows you to “learn” functions from your original remote control. For example - you may want to use your remote to operate the RANDOM PLAY feature from your original CD remote control. This remote is equipped with an “easy learning” feature that allows you to “learn” features (such as RANDOM PLAY from your original CD remote) by following the steps below, and on the next page: 1. Press and hold the SETUP button until the red indicator turns on, then release the button. 2. Press and release the desired mode button (TV, VCR, etc.), the red indicator blinks then stays on. 3. Press and release the LEARN button, the red indicator blinks then stays on. 4. Press and release the Learning Remote button that you want to teach (e.g. POWER). 5. Point both remotes facing each other by approximately 1 inch apart (see tips on page 14). 6. Press and hold the Original Remote button (e.g. Power) until the red indicator blinks once and stays on. If there is a learning problem, the indicator blinks for three seconds and stays on. If this happens, repeat Steps 4 to 6. 7. Repeat Steps 4-6 for other buttons you want to learn. 8. Press and release the SETUP button when all desired remote commands are learned. Code Learning is now complete. 6. Line up your remotes (that you’re learning from) in front of the Learning remote, on a hard surface approx. 1 inch apart. 4. 2. 1. 3. 16 17 Troubleshooting Clearing Commands To Clear all Learned Commands under a mode Remote does not operate your product. Clearing learned commands is helpful if, for example, you replace your CD player with another brand or model. If you had learned a feature from your old CD player’s original remote on to this remote (such as RANDOM PLAY), that feature would no longer work for your new CD player. Should you wish to remove or clear one or more “learned” commands, follow the steps below: 1. Press and hold the SETUP button until the red indicator turns on. Release the SETUP button. 2. Press and release the button for the mode you want to clear (TV, VCR, etc.). The red indicator blinks off. 3. Press and release the LEARN button TWICE. The red indicator blinks off. 4. Press and release the SETUP button. The red indicator turns off. All learned Commands under that mode are now cleared. Master Clear - To Clear all Learned Commands under all modes 1. Press and hold the SETUP button until the red indicator turns on. Release the SETUP button. 2. Press and release the LEARN button TWICE. The red indicator blinks off. 3. Press and release the SETUP button. The red indicator turns off. All Learned commands in the remote are now cleared. • Press the mode button of the product you want to control. • Progr...