Войти:
Оценок - 3, средний балл: 4.3 ( )

Инструкция по эксплуатации La Crosse Technology, модель Radio Controlled Analog Clock WT-3181bz

Производитель: La Crosse Technology
Размер: 139.33 kb
Название файла:
Язык инструкции:en
Перейти к скачиванию



К этому устройству также есть другие инструкции:

Фрагмент инструкции


Notes: • After the batteries have been installed a tone will sound, and the LCD (Liquid Crystal Display) will activate. • The indoor temperature/humidity will be displayed. Also, the time will appear as “-:--”. • The WWVB search is automatically initiated, and a tower icon appears and flashes with the time colon (no tower icon will appear if the WWVB is too weak to be detected, and the time display will remain on “-:--”). • While the WWVB search is being conducted various numbers will appear in the time display. • After 15 minutes, the projection alarm will either display the WWVB time, or discontinue the search if the time is not found. If the search is cancelled “-:--” will remain in the time LCD. • The projection alarm will conduct a WWVB search every hour until the first signal is found. • Once the WWVB time is found, a search is automatically conducted nightly at midnight. • If the signal is found at midnight, the tower icon will remain, if not, another search will take place every hour (until 6:00 am) until the signal is found successfully. • If no signal is found during this period, the tower icon will not appear and the clock will search again at 12:00 am the next night. • The radio-controlled time receiver is located on the bottom side of the projection alarm. When using the AC adaptor be sure to keep the adapter cord away from the bottom side of the unit as if the wire is too close it can cause weakened reception sensitivity. 5 II. PROGRAM MODE To enter the Program Mode hold down the “MODE/MIN” button for 3 seconds, until the time flashes in the top of the display. The Program Mode Guide is laid out in a manner that allows you to program each function separately, or you can follow the instructions entirely to program the projection alarm. Complete programming is usually done for the initial set-up, and will require you to skip step 1 and 2 of programming sections D and E. To exit the setting mode simply wait approximately 10 seconds for the projection alarm to automatically return to normal operation. A. PROGRAMMING SEQUENCE 1. Manual Time Display 2. Time Zone Setting 3. Daylight Saving Time On/Off B. FUNCTION BUTTONS There are 3 function buttons located on the front of the projection alarm and one on the top. The function buttons are labeled: AL/HOUR, light direction icon, MODE/MIN, and SNOOZE (the top bar). Mode Button (toggles between Alarm Button (also adjusts Display Direction indoor temp/hum and alarm the hours in time setting time. Also adjusts minutes in mode) time setting mode C. MANUAL TIME SETTING 1. Hold down the “MODE/MIN” button for 3 seconds, the time will flash in the Time LCD. 2. Press and release the “AL/HOUR” button to advance the hours and press and release the “MODE/MIN” button to advance the minutes. NOTE: “A.M.” or “P.M.” will be displayed to the left of the time to help identify the time. 3. Press and release the “SNOOZE” button to confirm the time setting and to advance to DST (Daylight Saving Time) setting. D. ...

Эта инструкция также подходит к моделям:
Пульт ду - WS-8158U-IT (139.33 kb)
Пульт ду - WS-8418U-IT (139.33 kb)
Пульт ду - WT-2100 (139.33 kb)
Пульт ду - WT-2150A (139.33 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории