Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
In your car and leaving your home you wish to turn off the outside lights near the garage, front door and rear door, as well as interior lights and appliances. Wireless Gateway SCENE 2 can be programmed to turn all of these modules OFF and to turn ON the security alarm. To operate SCENE 2 from your car, you will also need to program one button of the remote located in your car to SCENE 2. 3. Noises outside your home awaken you during the night. SCENE 3 is programmed to turn on only the outside lights. You can turn on SCENE 3 with your Keychain Remote from your bedroom to illuminate the area and scaring off any potential intruders. 4. Lights out! You have tucked your 2 children in bed and one has your permission to read for 15 minutes while the other has your permission to watch TV for 15 minutes. After 15 minutes you want to turn off their lights and TV. SCENE 2 is programmed to their bedroom lights, lamps and to a TV in the childs room. Using your Keychain Remote you can turn their lights and TV off. 1 -Wireless Gateway, RFBGD 1 -Keychain Remote, (RFKGT) or any built-in vehicular remote control 3 -Dimmer Switch, RF9534 (for each light switch) 2 -Lamp Module, RFLDM (for lamp in kitchen and family room) 1 -Wireless Gateway, RFBGD 1 -Keychain Remote, RFKGT 3 -Dimmer Switch, RF9534 (for each light switch) 2 -Switches, RF9501 (for exterior lights) 1 -Wireless Gateway, RFBGD 1 -Keychain Remote, RFKGT 2 -Dimmer Switch, RF9534 (for each light switch) 2 -Lamp Module, RFLDM (for lamp in kitchen and family room) 1 -Appliance Module, RFAPM (for the TV) ButtonCombinations Presstwotransmitterbuttonsatthesametime Use this procedure to program your Keychain Remote for up to 6 actions. In any of the previous programming instructions at the point where you need to activate a transmitter button to complete the programming step, simply simultaneously press a combination of any two buttons. Then to activate that programmed action, simultaneously press those two buttons. Example of Use: Single Big button is programmed only to activate Garage Door Opener, while each of the two smaller buttons are programmed to SCENE 1 and 2 of the Gateway Module. SCENE 3 of the Gateway module can be programmed to activate by pressing the two smaller buttons at the same time. Troubleshooting Problem: The range of the transmitter is reduced. Problem: The LED (light) on the transmitter does not turn on when pressed. Solution: Replace Battery. Solution: To change the batteries, insert a coin in the coin slot and twist to access the battery compartment. Your transmitter may use one or two CR2016 batteries. Remove the batteries from the battery cage and replace with fresh batteries. Be sure to maintain the correct polarity (+). Coin Slot TroubleshootingProblem: OneofmyWirelessGatewaySCENESisnotworking. Problem: Myoperatornolongerworkswithmyremote. Solution: The Cooper Wiring Devices Wireless Gateway can be activated by up to 12 transmitter programs. When exceeded the last one programmed will be dropped. Solution: The Wayne Dalton operator can be activated by up to six remote control devices (including wall station and keyless entry controls). If a seventh control is programmed, one of the programmed controls will be overwritten and will no longer activate the operator. To clear the programming of all remote control devices, press and hold the DoorMaster™ light fixture program button, idrive®, Quantum™ or Classic drive™ operator program button for approximately ten seconds. When the DoorMaster™, Quantum™, Classic drive™ status LED goes out or idrive® operator beeps three times, then all controls are erased. Compliance Covered by one or more of the following Wayne Dalton Patents D413,055; D413,579; D413,867; D421,031; D472,568; D472,910; D473,573; D473,574; D505,393; 5,929,580; 5,931,212; 6,078,249; 6,161,438; 6,145,570; 6,164,014; 6,325,134; 6,326,751; 6,326,754; 6,401,792; 6,561,255; 6,561,256; 6,568,454; 6,588,156; 6,605,910; 6,667,591; 6,739,372; 6,845,804; 6,851,465; 6,873,127; 6,880,609; 6,903,650. Other US and Foreign Patents pending. Z-Wave™ is a trademark of Zensys Corp. FCCandICStatement FCC Regulatory Information: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: a) reorient or relocate the receiving antenna, b) ...
Эта инструкция также подходит к моделям:Пульт ду - ASPIRE RF RFKGT (411.69 kb)