Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
Setting g. Point your original Caring for the environment setting. The TV mode key light will bottom end of your recycling 4. Press and release the turn off indicating successful Use the +H and +M the IR elements on This symbol on an AT&T The TV mode key light turns All The volume commands Hours and Minutes for directly in line with each product means the product learned Commands in the for different devices. the +H and +M buttons are diagram to the right). You may need should not be disposed of now cleared. 3. On your U-verse remote control, bottom on your new Charging Base. to adjust the height of either with household waste. and release the key that you want NOTE: achieve this. A. Manual Programming E. Resetting the remote control to the teach. If a programmed mode key has no H-II. Finding more than one remote h. Avoid learning your original remote's Factory Default Settings 4. While pointing your original remote at commands of its own, then the volume Volume/Mute keys unless you are sure Disposal of your charging base, power Use the following steps to set up the TV, the bottom of your U-verse remote control will normally operate the TV. If If there is more than one remote and these operate the same device. supply or remote control. DVD or AUX mode keys: 1. Press and hold the TV key and while approximately 1 inch apart, press and an invalid key is pressed, the selected Charging Base, you can set each Charging i. Avoid learning your original remote's holding it pressed, press the OK key hold the original remote key until the mode key light flashes for 3 seconds and Base to find only its own remote with 16 VCR or DVD transport keys unless Please do not dispose of any of the items 1. Power on the device you want to for one second and release both keys mode key light blinks once and stays turns off. The remote control returns to unique codes. With the first power up of you’re sure these operate the same in this package with your householdprogram and locate the 4-digit code on. (If there is a learning problem, the at the same time. normal operation and you will need to the Charging Base, it will be set to find device. waste. These items should be disposed of from the code list. 2. All the mode keys will flash and the mode key light blinks for three seconds start over. If no key is pressed within 30 ALL remotes. j. If learning the first or second keys for accordance with the national collection 2. Press and hold the mode key (TV, and stays on. If this happens, repeat TV mode key light will stay on. seconds, the remote control times out, the a mode results in continuous errors and recycling schemes operated by your DVD, or AUX) and while holding it 3. Press and hold the DELETE key for 3 the steps above.) selected mode key light flashes for 3 To set the Charging Base so that it finds then try the following: local or regional authority. Alternatively pressed, press the OK key for one seconds until the TV mode LED blinks seconds and turns off. The remote control a specific remote when there are multiple i. End the learn session by pressing the you may return unwanted items to anysecond. and stays off. The remote control is returns to normal operation at which time remote in the household, follow these LEARN key. approved AT&T Service Center in your now reset to factory default settings. 3. Release both keys and all of the you can start over. instructions: ii. Clear out the learned commands for region. mode keys will flash then the If you want to use the remote control that mode. for your TV and other devices, you will Code List selected mode key light will stay lit. G. Battery saving backlight 1. Press and hold both clock setting keys iii. Check the IR elements are correctly AT&Tneed to set up the TV, DVD and AUX aligned between the two remotes. 4. Enter the 4-digit code by pressing the cancellation feature (+H and +M) at the same time for 3numerical keys (0-9). The selected U-verse mode keys. TV seconds. The display shows the iv. Adjust the distance between the two mode key light will blink for each digit remote 4. If no key is pressed within 30 seconds, In order to extend the life of your battery current ID, from 1 to 16 or ALL. remotes to be closer (e.g. half an inch) Abex 0185 the remote control times out. The entry and will remain off after the entry between charges, your U-verse remote 2. Press the +M key to cycle from 1 to or a further away (e.g. 2 inches) from Acme 0010of the fourth digit - indicating a selected mode key light flashes for 3 control has the ability to toggle between 16 including a selection for all remotes each other. Admiral 0020 0226 0001 successful set up. seconds and turns off. The remote turning the backlights on or off. If you in the household. v. Try learning the original remote for Advent 0116 0176 0922 control returns to normal operation 5. Point the remote control at the selected wish to use this feature, follow these in- 3. Then press the +H key to confirm the that mode again. If...