Оценок - 6, средний балл: 3.8
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Mounting hardware WT-8002U 3. Instruction manual Digital Clock with Indoor Temperature Features and Specifications . Digital time and date . 12/ 24 hour time . Indoor temperature (°F or °C) (32°F to 122°F - 0°C to 50°C) . Time alarm with snooze . Calendar: month, date and weekday . Wall hanging or free standing . Battery: 1 X “AA” size 1.5V (not included) . Battery life: Up to 24 months . Dimensions: 8.62" L x 1.29" W x 6.81" H (218.9 x 32.7 x 172.9 mm) Back View La Crosse Technology, Ltd. lacrossetechnology. com 2809 Losey Blvd. S La Crosse, WI 54601 Phone 608-782-1610 Table of Contents Table of Contents ......... .......... .......... .......... ....... 1 Inventory of Contents ... .......... .......... .......... ....... 2 Features and Specifications ... .......... .......... ....... 2 Back View.. .......... .......... .......... ......... .......... ....... 2 Button View ......... .......... ......... .......... .......... ....... 2 Install Battery...... .......... .......... .......... .......... ....... 3 Set the Time and Date... ......... .......... .......... ....... 3 To Change the Temperature Unit…… ………… ……… 4 To Set the Time Alarm ... ......... .......... .......... ....... 4 To Use The Alarm ........ .......... .......... .......... ....... 4 Battery Replacement Information ..... .......... ....... 5 Mounting the Unit ......... .......... .......... .......... ....... 5 Online Resources......... .......... .......... .......... ....... 5 Care and Maintenance . .......... .......... .......... ....... 5 Troubleshooting ... ......... .......... .......... .......... ....... 6 Warranty Information .... .......... .......... .......... ....... 6 Page 1 of 8 Button View Page 2 of8 Install Battery Install Battery Insert 1 new "AA", 1.5 volt ALKALINE batteries into the clock according to the polarity marked on the battery compartment. Once the battery is properly installed in the clock, the unit will beep and all segments of its LCD will briefly light up. The indoor temp and the time (displayed as 12: 00) will appear on the LCD. If the time and temp do not appear after 30 seconds, please reinstall the battery and try again. Once the indoor temp is displayed, proceed to the next step. Set the Time and Date Please read through all of the steps below before starting to configure your clock. Once you have started the configuration, you will be able to move from one step to another by pressing the “ SET” button. If at any point during the setup process you need to start over, avoid pressing any buttons for roughly 30 seconds or wait until the display stops flashing, then repeat the steps outlined in this section. Note: The following steps often refer to two buttons: “+ ” and “ - / °F/ °C”. The “+ ” button is used to increase setting values and the “ -/ ° F/° C” button is used to decrease setting values. To enter setup mode and begin the configuration process, press and hold the “ SET” button for about 3 seconds, or until the clock beeps. The ...
Эта инструкция также подходит к моделям:Пульт ду - Radio Controlled Projection Alarm WT-5110 (95 kb)
Пульт ду - Radio Controlled Projection Alarm WT-5350 (95 kb)
Пульт ду - TIMER WALL WT-8100 (95 kb)
Пульт ду - Wireless 433 MHz Temperature Station WS-7136U (95 kb)