Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
For example (assume TV is blinking): 1) Press the AUTO CH UP button and AUX starts blinking 2) Press the DVD button and DVD in the Menu starts blinking • Level Adjust Once the Source has been selected, use the MANUAL SEEK buttons [B] to adjust its Level up or down. As the level is adjusted, the bar centered at zero (default) will extend to either the positive or negative direction. At the same time, the numerical indicator (initially 0) will either increase (maximum = 7) or decrease (minimum = –7). Listen to each output and match levels according to your personal preferences. NOTE: Any button, besides the ones used in the adjustment process, can be pressed to leave the Level Adjustment screen. A B 9 OPERATION - TV Tuner Control Functions Channel Selection 3. Direct Channel Select (Numeric keypad 0 - 9) To select the desired channel, press any of the 10 numeric keys (0 to 9) directly. These keys are also used as the Channel Preset keys. As soon as you press a key, the number that you selected is displayed in the OSD. TV MODE: When you enter ‘02’ to ‘69’ (or any two digit number), the desired channel appears immediately and the OSD disappears in about 3 seconds. When you enter ‘2’ to ‘9’ (or any 1 digit number), it will change to the desired channel after a 3 second delay and the OSD disappears in 3 seconds. __ CH 24 When an invalid CH (Channel) is selected, the current CH will not change and the OSD will disappear in 3 seconds. CABLE MODE: When you enter 001 to 125 (or any 3 digit number), the desired channel appears immediately and the OSD disappears in about 3 seconds. When you enter less than three digits, it will change to the desired channel after 3 seconds delay and the OSD disappears in about 3 seconds. When an invalid CH is selected, the current CH does not change and the OSD will disappear in 3 seconds. 4. CH DOWN/UP Key Use the AUTO CH and MANUAL SEEK Arrow keys to select the desired TV channel. AUTO CH DN/UP Keys Use this key to select any CH which was set by the AUTO PROGRAM function. Press the UP or DOWN keys to move up or down in sequential order. MANUAL SEEK DN/UP Key This key has two functions as follows. • Press and release: Channel moves UP or DOWN one frequency at a time (whether a station exists or not). • Press and Hold: Press and hold the UP or DOWN key for at least 2 seconds to seek up or down to the next valid station. NOTE: If the tuner does not find a valid CH during the seek mode, it will stop after all channels have been checked. 10 OPERATION - TV Tuner Control Functions 5. BAND Key Use the BAND Key to choose between TV mode and CABLE mode. Most of time TV mode is used for the mobile environment. However, should a camp site or RV Park have a cable TV hook-up, CABLE mode may be used.* After pressing the BAND key, the OSD will display the current status (blinking). Pressing the key again, will toggle between the TV and CABLE BAND. After 8 seconds or when any other key is pressed, the OSD display will disappear and changes will be set. TV CABLE TV / CABLE SELECTION TV/CABLE Selection screen TV Blinking indicates current mode. * To connect CABLE TV, an F-connector-to-mini-phono jack adapter must be used. This is available at any electrical parts shop. Plug the adapter into any one of 4 Diversity antenna input jacks. The TV Band can receive up to 68 channels (2-69). The CABLE Band can receive up to 125 channels (1-125). The total number of channels available for both TV and Cable TV is 181 (after subtracting the redundant 12, channels 2 through 13). 6. AUTO PROGRAM (A.PGM) Key AUTO PROGRAM memorizes only receivable channels in the current band. AUTO PROGRAM memory is available on both TV and CABLE Bands. Each memory can be either LOCAL or TRAVEL. This gives a total of 4 memories. This is very useful to store stations near your home in LOCAL memory and then use TRAVEL memory when on vacation in an unfamiliar region. This key has two functions as follows: • Press and release: Switch LOCAL and TRAVEL Press and release the A.PGM key [A]. The OSD will display the current status [B] (blinking). Pressing the key again toggles between the two Modes (LOCAL and TRAVEL). After 8 seconds or when any other key is pressed, the OSD display disappears and any change made is set. A 11 LOCAL TRAVEL AUTO PROGRAM (PRESS&HOLD >SET) B OPERATION - TV Tuner Control Functions • Press and Hold: Start AUTO PROGRAM While the OSD is displayed, press and hold the same key for at least 2 seconds, AUTO PROGRAM begins searching the selected band for receivable channels. The status of the search is shown in the OSD (see below). Once the AUTO PROGRAM starts, it cannot be stopped until the entire band is scanned. AUTO PROGRAM SCANNING TV LOCAL SEARCH CH XX 7. PRESET Key The PRESET key is able to assign any channel to any of the numeric keys 0 to 9. The TV and CABLE Bands can have up to 10 presets each. This memory is entirely separate from the AUTO PROGRAM memory. This key has two functions as follows. • Press and releas...