Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
Your recording can be up to three seconds long. Fig. 26 - Memory Button 4. After three second there will be a “beep” to tell you recording has stopped. Your recording will be played back immediately so you can check it, followed by a “beep-beep” sound. 5. Now you can repeat steps 3 and 4 if you want to change your announcement or if you want to record an announcement for a different memory button. 6. Otherwise, when you are finished recording, hang up the handset. 7. Slide the ANNOUNCEMENT switch to the CUSTOM position and your recordings will be played when you press a memory button. E N G L I S H Fig. 27 - Setting Custom Announcements M. Recording Number Button Announcements The JV-35 also comes with factory pre-recorded announcements for the F R A N C A I S 15 Operating your JV-35 Operating your JV-35 number buttons. If you choose, you can record announcements for the number buttons in your own voice by following these steps. 1.Pick up the handset. 2.Slide the ANNOUNCEMENT switch to the PROG position. You will hear “Program Mode, Program Mode” followed by a “beepbeep” sound to confirm the JV-35 is ready to be programmed. Fig. 28 - Announcement Switch 3. Press the 1 button. After the “beep,” say “One” in your own voice or language. Your recording can be up to one second long. Fig. 29 - Keypad Programming 4. After one second there will be a “beep” to tell you recording has stopped. Your recording will be played back immediately so you can check it. Then there will be a “beep-beep” sound. 5. Now you can repeat steps 3 and 4 for all Operating your JV-35 Operating your JV-35 the rest of the number buttons. 6. When you are finished recording, hang up the handset. 7. Slide the ANNOUNCEMENT switch to the CUSTOM position. Your announcements will be played when you press a number button. Fig. 30 - Custom Announcements N. Selecting Number Button Announcements To hear the number button announcements that were pre-recorded at the factory, slide the ANNOUNCEMENT switch to PRESET. Fig. 31 - Preset Announcements To hear the number button announcements that you have recorded, slide the ANNOUNCEMENT switch to CUSTOM. E N G L I S H Fig. 32 - Setting Custom Announcements Operating your JV-35 Operating your JV-35 To turn off the voice announce feature, turn the phone over and slide the “VOICE ANNOUNCE” switch to OFF. Fig. 33 - Setting Voice Announce O. Direct Audio Connection To connect an assistive listening device, plug a compatible auxiliary cable into the Audio Output port, then plug the other end into your assistive listening device. When you have an assistive listening device connected, you still must speak into the handset. Note: The Audio Output port is compatible with some neck- loops. Please check with your hearing aid specialist. It can also be used with a cochlear implant. P. Cochlear Implant Adapter Cord A cochlear implant adapter cord is available from Ameriphone that can be used to plug the JV-35 directly into a speech processor. Fig. 34 - Audio Output port Location Operating your JV-35 Operating your JV-35 Connecting the Speech Processor: Caution: Before plugging any cord into your speech processor, you must consult your implant manufacturer. • Plug the mono end of the plug into the speech processor. • Plug the stereo end of the plug into the Audio Output socket on the phone. • Speak into the handset when using the cochlear implant adapter cord. E N G L WARNING! During I thunderstorms, avoid using S telephones as electric shock H from lightning can occur. Troubleshooting Chart Troubleshooting Chart If any problem should arise during operation of your JV-35, go through the suggestions listed below. Should the difficulty persist, contact Ameriphone or your authorized dealer for assistance. SYMPTOM CAUSE AND CORRECTIVE ACTION No dial tone Check all phone cord connections. No number No number dialed when stored in that memory button memory button.See "Programmingpressed Frequently Dialed Numbers Call cannot be dialed, or is dialed slowly See "Installation" section to reset the dial mode switch. No audible ring Make sure the ringer is not set to "Off" position. Phone Check all the ”locks up“ connections. no functions Make sure the operate cords are plugged in correctly. Regulatory Compliance Regulatory Compliance Part 68 of FCC Rules Information This equipment complies with Part 68 of the FCC rules. On the bottom of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, this information must be provided to the telephone company. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug, RJ11 USOC, is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for ...