Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
You can continue Fig. 11 - BOOST Button 2. Adjust the TONE selector to suit your hearing. D. Ringer Volume Adjust the RINGER control to suit your hearing. HOLDTONELo HiVOLPROGBOOSTMEMORYREDIAL HOLDTONELo HiVOLPROGBOOSTMEMORYREDIAL Fig. 12 - Tone Slide Fig. 14 - Hold Button Tone PulsePreset Prog CustomRINGERANNOUNCEMENTLo Med Hi Fig. 13 - Ringer Switch 9 Operating your JV35 your call on the other phone. F. Last Number Redial Lift the handset and press the REDIAL button to dial the last number you dialed. HOLDTONELo HiVOLPROGBOOSTMEMORYREDIAL HOLDTONELo HiVOLPROGBOOSTMEMORYREDIAL Fig. 16 - PROG Button Fig. 15 - Redial G. Programming the Emergency buttons The Emergency buttons can be programmed to dial numbers with one touch. You may wish to use these buttons for police, fire or medical response. 1. Lift the handset and press the PROG button. 2. Enter the phone number as you would normally dial it. Fig. 17 - Entering Number 10 Operating your JV35 3. Press PROG button again. 4. Press one of the Emergency buttons. 5. Hang up the handset. 6. The number is now stored within the Emergency button you selected. 7. To change a stored number or to program another memory button, repeat this process from step 1. H. Dialing With An Emergency Button 1. Lift the handset. 2. Press one of the Emergency buttons. You will hear an announcement similar to “Emergency One” and then the number you have stored for that button will be dialed automatically. I. Programming Frequently Dialed Numbers 1.Lift the handset and press the PROG button. JV35 Fig. 18 - Emergency Button 11 Operating your JV35 HOLDTONELo HiVOLPROGBOOSTMEMORYREDIAL Fig. 19 - PROG Button 2. Enter the phone number as you would normally dial it. 3. Press the PROG button again. 4. Press MEMORY, then one of the number buttons: 0, 1, 2, 3, etc. Note: # and * keys are not available for this function. 5. Hang up the handset. 6. The number is now stored within the number button you selected. 7. To change a stored number or to program another memory button, repeat this process from step 1. Fig. 20 - Entering Number 12 Operating your JV35 J. Memory Dialing 1. Lift the handset. 2. Press MEMORY and one of the number buttons. factory pre-recorded announcements to identify each Emergency button such as “Emergency One,” etc. You can erase these identification announcements and record announcements of your own, such as “Police” or “Fire” by following these steps: 1.Pick up the handset. 2.Slide the ANNOUNCEMENT switch to the PROG position. You will hear “Program Mode, Program Mode” followed by a “beep- beep” sound. This confirms the JV35 is ready to be programmed. HOLDTONELo HiVOLPROGBOOSTMEMORYREDIAL Fig. 21- Memory Button You will hear an announcement such as “Memory One” and then the number you have stored for that button will be automatically dialed. K. Recording Emergency Button Identification Announcements The JV35 comes with 13 Operating your JV35 Tone Pulse Preset Prog CustomRINGERAUDIOOUTPUTANNOUNCEMENTLo Med Hi 4. After three seconds there will be a “beep” to tell you recording has stopped. Your recording will be played back immediately so you can check it, followed by a “beep-beep” sound. 5. Now you can repeat steps 3 and 4 if you want to change your announcement or if you want to record an announcement for a different Emergency button. 6. Otherwise, when you are finished recording, hang up the handset. Fig. 22 - Announcement Switch 3.Press the desired Emergency button. After the “beep,” speak into the handset to record an announcement like “Police” or “Fire” for that button. Your recording can be up to three seconds long. JV35 Fig. 23 - Emergency Button 14 Operating your JV35 7. Slide the ANNOUNCEMENT switch to the CUSTOM position and your recordings will be played when you press an Emergency button. Tone Pulse Preset Prog CustomRINGERAUDIOOUTPUTANNOUNCEMENTLo Med Hi Fig. 24 - Custom Announcement L. Recording Memory Button Identification Announcements Factory pre-recorded announcements identify each memory button. You can erase these announcements and record your own announcements, such as “Bob’s Number” or “Bank.” Record announcements by following these steps: 1. Pick up the handset. 2. Slide the ANNOUNCEMENT switch to the PROG position. You will hear “Program Mode, Program Mode” followed by a “beep-beep” sound to confirm the JV35 is ready to be programmed. Tone Pulse Preset Prog CustomRINGERAUDIOOUTPUTANNOUNCEMENTLo Med Hi Fig. 25 - Programming Announcement 15 Operating your JV35 3. Press the MEMORY button plus the desired number buttons (0, 1, 2,etc.). After the “beep,” record an announcement like “Bob’s number” or "Bank” for that button. Your recording can be up to three seconds long. 5. Now you can repeat steps 3 and 4 if you want to change your announcement or if you want to record an announcement for a different Memory button. 6. When you have finished recording, hang up the handset. 7. Slide the ANNOUNCEMENT switch to the CUSTOM position and your recordings will be...