Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
It is highly recommended that you complete the resident listing in the appendix prior to starting any programming from the keypad. This listing will provide you with the information needed to complete the manual programming sequence. This symbol _ in the programming steps indicates numbers that you will need to enter, one number per symbol. When programming from the keypad, after each programming step is performed correctly, a short tone (beep) will be heard. When the programming session is ended, a long tone (beeeeeep) will be heard. 3.1.2 Programming with an IBM Keyboard The 5-pin keyboard connector is located on the bottom of surface mount units, and inside the faceplate of the flush and wall mount units. 1. Insert the 5-pin keyboard connector into the matching connector in the telephone entry system. 2. Follow the instructions as described in each section with the following exceptions: Use the ENTER key on the keyboard in place of the * key. Use the ESC key on the keyboard in place of the # key. Use the END key on the keyboard in place of 0# together input. NOTE: When programming resident names from the keyboard, it is not necessary to press the ENTER key after each letter as indicated in the programming instructions. Type the entire name and then press the ENTER key. 3.1.3 Programming with a Touch-Tone Telephone Programming from a touch-tone telephone should only be attempted after you are familiar with the programming steps in this manual. NOTE: Resident names and the scrolling messages cannot be programmed by this method. 1. Call the telephone number that the entry system is installed on from a touch-tone telephone. The system will answer after the second ring and respond with a one second tone (beep). 2. Follow the programming instructions as described in each section of this manual. 3. When completed with a programming step, simply hang-up. You cannot press the *# together from a touch-tone telephone. 3.1 PROGRAMMING INFORMATION 3.2 GENERAL PROGRAMMING 3.2.1 Master Code This programming step sets the system MASTER CODE. The master code is the four-digit number required to gain access to the system memory. You need to know the master code prior to programming the system with the PC, or to perform any of the programming functions on the following pages. NOTE: The master code cannot be programmed from an off-site location. The master code can only be programmed from the system keypad. Factory setting = 9999 1. Open the cabinet of the telephone entry system and turn the master code switch (the small toggle switch) on. 2. Enter a four-digit master code _ _ _ _ then press * (beep). 3. Turn the master code switch off and close the cabinet. 3.2.2 Single or Multiple Systems This program sequence sets the telephone entry system to operate as a single unit on the phone line, or to share the phone line with other units. If multiple systems are sharing the same phone line, then each one must be set as a "multiple system" and each must have a unique master code. Factory setting = Single System. 1. Press * 0 4 and then enter the four-digit MASTER CODE _ _ _ _ (beep). 2. Enter 0 * (beep) for a single system or 1 * (beep) for multiple systems. 3. Press 0# TOGETHER to end this programming step (beeeeeep). 3.2.3 Programming for Call-up Operation This feature is only used when the telephone entry system is interfaced with a DoorKing 1816 Telephone Intercom system under certain special applications. The factory setting for this feature is OFF. Do not change this feature to ON. Refer to the 1816 Installation Manual, and check with your DoorKing representative on the special applications that this feature is used for. Factory Setting = OFF 1. Press * 7 8 and enter the four-digit MASTER CODE _ _ _ _ (beep). 2. Enter 0 * (beep) to turn the call up feature OFF. Enter 1 * (beep) to turn call up ON. 3. Press 0# TOGETHER to end this programming step (beeeeeep). DIGIT 2nd Relay hold. Relay will activate and remain activated until commanded to release. 3rd Relay release. Deactivates the relay hold command. 4th Relay hold 1-hour. Relay will activate for 1-hour and then will automatically deactivate itself. 3.2.4 Relay Strike Time These steps will program Relay 1 and Relay 2 strike times. Strike times can be programmed from 1/4 second (enter 00 in step 4) up to 99 seconds by entering the desired time in seconds. Factory setting for relay strike times are: Relay 1 = 01, Relay 2 = 01. 1. Press * 0 3 and enter the four-digit MASTER CODE _ _ _ _ (beep). 2. Press 1 * to set relay 1, or 2 * to set relay 2 strike time. 3. Enter the two-digit strike time _ _ (00-99) then press * (beep). 4. Repeat steps 2 and 3 to set the other relay strike time. 5. Press 0# TOGETHER to end this programming step (beeeeeep). 3.2.5 Talk Time This programming sequence sets the maximum time allowed for conversation when the entry system places a call to the resident. The talk time can be set from 1 second up to 255 seconds (4 minutes, 15 seconds) and is entere...