Оценок - , средний балл:
(
)
)
Производитель: GE
Размер: 1.05 mb
Название файла: 19267a89-5123-455d-8c49-cdeeef8987e3.pdf
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
Before You Begin Parts Checklist Make sure your package includes the following items: Modular Jack Requirements To properly connect your phone to your telephone lines, you should identify the type of wall jack(s) you have. You will need an RJ11C (for a single line) or a RJ14C (for two lines) type modular phone jack, which might look like the one pictured here. If you don’t have either modular jack, call your local phone company to find out how to get one installed. Important Installation Information • Never install telephone wiring during a lightning storm. • Never touch uninsulated telephone wires or terminals, unless the telephone line has been disconnected at the network interface. • Use caution when installing or modifying telephone lines. • Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. • Temporarily disconnect any equipment connected to the phone, such as faxes, other phones, or modems. Base Layout Installation & Setup CAUTION: Disconnect the phone cord from the wall outlet before installing or replacing the batteries. Installing the Batteries Your Caller ID phone uses 4 AA-size alkaline batteries for receiving and storing Caller ID records and for storing the numbers you use for memory dialing, pulse dialing, redial, and predial functionality. 1. Release latch on battery compartment and remove cover. 2. Insert 4 AA-size alkaline batteries as shown on the diagram in the battery compartment. 3. Snap the battery compartment door back into place and replace the mounting bracket. 4. If the line cord was previously connected, re-attach it to the unit and check your memory locations. NOTE: If the low battery icon appears in the display, you need to replace the batteries. It is important that you replace the batteries as soon as possible in order to maintain Caller ID operation. IMPORTANT: If you are not going to use the telephone for more than 30 days, remove the batteries because they may leak and damage the unit. Installation Desktop Installation To attach the desktop pedestal: NOTE: Ensure the handset hook is in the DESK position. Adjust it by pushing up and out of the slot on the base with your thumb, rotate the hook 180°, and replace it back in the slot. To connect LINES 1 + 2: There are two possible connections. Refer to Figure 1 if you have one single line (RJ11C) phone jack or one dual-line (RJ14C) phone jack. 1. Connect one end of either straight telephone line cord to the jack marked Line 1+2 on the back of the base. 2. Connect the other end to the single-line or dual-line wall phone jack. NOTE: If you connect the telephone line cord to the single-line (RJ11C) wall phone jack, you will only be able to use one telephone line (either Line 1 or Line 2) but not both lines simultaneously. Refer to Figure 2 if you have two single-line (RJ11C) phone jacks. 1. Connect one end of either straight telephone line cord to the jack marked Line 1+2 on the back of the base. 2. Connect one end of the other straight telephone line cord to the jack marked Line 2 on the back of the base. 3. Connect the other end of each straight telephone line cord to the two single line wall phone jack. 4. Plug one end of the coiled handset cord into the handset and the opposite end into the base. 5. Set the Ringer Line 1 and Ringer Line 2 volume switches located at the back of the base to the desired loudness. OFF - Telephone will not ring. LO - Sound will be lowest. HI - Sound will be loudest. 6. Press the Line 1 button if the Line 1 telephone cord is connected. Otherwise, press Line 2. 7. The unit is properly installed if you pick up the handset and hear the dial tone. Otherwise, recheck all installation steps. To detach the desktop pedestal: Wall Mount Installation Your speakerphone can also be mounted on a wall plate (not included). NOTE: To prevent the handset from falling out of the cradle while the phone is hanging on the wall, you must set the handset hook (located on the base) in the WALL position. You will also need to remove the desktop pedestal if attached. To connect LINES 1 + 2: There are two possible connections. Refer to Figure 1 at beginning of Installation section if you have one single line (RJ11C) phone jack or one dual-line (RJ14C) phone jack. 1. Connect one end of either straight telephone line cord to the jack marked Line 1+2 on the back of the base. 2. Connect the other end to the single-line or dual-line wall phone jack. NOTE: If you connect the telephone line cord to the single-line (RJ11C) wall phone jack, you will only be able to use one telephone line (either Line 1 or Line 2) but not both lines simultaneously. Refer to Figure 2 at beginning of Installation section if you have two single-line (RJ11C) phone jacks. 1. Connect one end of either straight telephone line cord to the jack marked Line 1+2 on the back of the base. 2. Connect one end of the other straight telephone line cord to the jack marked Line 2 on the back of the base. 3. Connect t...