Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
HEARING AID COMPATIBILITY This telephone system meets FCC standards for Hearing Aid Compatibility. FCC NUMBER IS LOCATED ON THE CABINET BOTTOM REN NUMBER IS LOCATED ON THE CABINET BOTTOM Model 2-9410 15363750 (Rev. 0 E/S)P.O. Box 1976, Indianapolis, IN 46206 © 1998 Thomson Consumer Electronics, Inc. Printed in Philippines Trademark(s) ® Registered Marca(s) Registrada(s) BEFORE YOU BEGIN MODULAR JACK REQUIREMENTS You need an RJ11C or RJ14C type modular jack, which is the most common type of phone jack and might look like the one pictured here. If you don’t have a modular jack, call your local phone company to find out how to get one installed. BATTERY INSTALLATION BATTERIES FOR SUPPLEMENTARY POWER Four “AA”-size alkaline batteries (not included) provide power for LINE 1 and LINE 2 indicator lights. If you want the line indicators to light when a line is in use or ringing, install the optional batteries. Battery INSTALLING THE BATTERIES compartment Disconnect the line cords from the back of the unit and wait a few seconds for the unit to go into standby. 1. Use a screwdriver or other flat tool to open the battery compartment door. 2. Insert 4 “AA” size batteries as shown on the diagram in the battery compartment. 3. Close the battery compartment door securely. NOTE : If one line is disconnected (i.e., unplugged from the phone jack), the indicator light for that line will stay lit until the line is reconnected or the batteries for that line are removed. BATTERIES FOR BACKUP MEMORY A consumer replaceable long-life lithium battery (1.5V) is installed in the phone to provide backup power for retaining numbers in memory. The lithium battery compartment is located under the memo log on the base. 1. If telephone is wall mounted, remove from mounting. 2. Unplug modular jack from the phone wall outlet. Battery cover 3. Remove memo log to expose battery compartment. 4. Using a pointed object, open the battery door and remove. 5. Insert a pointed object down on the battery to push it up on one end. Turn over phone and allow battery to fall out. 6. Insert replacement battery, positive side up, and replace door. 7. Replace wall mount. 8. Plug the phone into modular jack. 9. You may have to reprogram some or all of the numbers into memory. 1 2 line 1 line 2 hold BATTERY SAFETY PRECAUTIONS • Do not disassemble, mutilate, puncture, wet, or dispose of battery in fire. Like other batteries of this type, if it is burned or punctured, it could release toxic materials which can cause injury. GENERAL PRODUCT CARE To keep your telephone working and looking good, follow these guidelines: • Avoid putting it near heating appliances and devices that generate electrical noise (for example, motors or fluorescent lamps). • DO NOT expose to direct sunlight or moisture. • Avoid dropping the unit and/or other rough treatment. • Clean with a soft cloth. • Never use a strong cleaning agent or abrasive powder because this will damage the finish. • Retain the original packaging in case you need to ship it at a later date. INSTALLATION DESKTOP INSTALLATION A coiled handset cord and three straight telephone line cords are packaged with your unit. 1. (See Figure 1) If you have one dual-line phone jack (RJ14C). Plug the white straight cord in the LINE 1+2 jack at the back of the base. Plug the opposite end of the cord into the modular RJ14C dual-line jack. (See Figure 2) or if you have two single-line phone jacks (RJ11C). Plug the straight cord in the LINE 1+2 jack at the back of the base. Plug the other straight cord into the LINE 2 jack. Then, plug the opposite end of the cords into the modular RJ11C jacks. 1 2 line 1 line 2 hold 1 2 line 1 line 2 hold Figure 1 Figure 2 2. Plug one end of the coiled handset cord into the handset and the opposite end into the base. 3. Set the RINGER 1 and RINGER 2 volume switches to HI, LO or OFF. Note in OFF position that line will not ring. Your telephone has separate and distinct ringer sounds for each line. This will allow you to determine (audibly) the line of an incoming call. 4. Set mode switch to TONE. Note that if you have problems dialing, switch to PULSE. 1 2 line 1 line 2 hold FLASH MEM DIALSTORE REDIAL B CA PULSE TONE 7 8 1 2 3 4 5 6 9 ABC DEF JKLGHI MNO TUVPQRS WXYZ * 0 #OPER EMERGENCY QUICK DIAL TONE HI LO OFF RINGER WALL MOUNT INSTALLATION 1. Follow Steps 1-4 of Desktop Installation, using the short telephone cord for Step 1. 2. Feed the short telephone cord through the grooves provided so that the base area is flat and ready to mount on the wall. 3. Place the base over the screws on the wall plate (not included) and gently slide the phone down into place. TROUBLESHOOTING TIPS Problem Solution TELEPHONE OPERATION MAKING AND RECEIVING CALLS CHOOSE A LINE • Press LINE 1 or LINE 2. When the handset is off hook, an indicator lights beside the button indicating the line is in use. To Make a Call To Receive a Call 1. Pick up the handset. 1. Press the line number of the flashing indicator. 2. Press LINE 1 ...