Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Create New Network Press the Learn button on the new intercom until a beep is heard. Within 10 seconds put the second intercom into Learn Mode (refer to the following table). Add to an Existing Network Press the Learn button on the new intercom until a beep is heard. Within 10 seconds put any networked intercom into Learn Mode (refer to table below). Press and release the Talk button to verify network is complete. INTERCOM LEARN MODE Press the Learn button until a beep is heard. Press and hold both buttons for 5 seconds. OR Each intercom will emit a tone when programmed into network. Repeat for any additional intercoms. Each intercom will emit a tone when programmed into network. Repeat for any additional intercoms. NOTE: Do not program new intercoms to each other before adding them to the network or they will form a separate network and the memory will need to be cleared. INTERCOM LEARN MODE Press the Learn button until a beep is heard. Press and hold both buttons for 5 seconds. OR Assemble Intercom Step 1 Step 2 Install 4 AA Alkaline batteries (not provided). (Lithium batteries recommended for colder environments.) Programming Intercom Adhere rubber pads to bottom. Repeat Steps 1 and 2 for any additional intercoms. The intercom must be programmed to at least one other intercom to become a network or it can be programmed into an existing network. Create New Network Press the Learn button on the new intercom until a beep is heard. Within 10 seconds put the second intercom into Learn Mode (refer to the following table). Add to an Existing Network Press the Learn button on the new intercom until a beep is heard. Within 10 seconds put any networked intercom into Learn Mode (refer to table below). Press and release the Talk button to verify network is complete. INTERCOM LEARN MODE Press the Learn button until a beep is heard. Press and hold both buttons for 5 seconds. OR Each intercom will emit a tone when programmed into network. Repeat for any additional intercoms. Each intercom will emit a tone when programmed into network. Repeat for any additional intercoms. NOTE: Do not program new intercoms to each other before adding them to the network or they will form a separate network and the memory will need to be cleared. INTERCOM LEARN MODE Press the Learn button until a beep is heard. Press and hold both buttons for 5 seconds. OR 2 Troubleshooting Intercom does not function. Check batteries in intercom. If using an AC Adapter ensure that it is plugged in. Ensure intercom is connected to a network. See Programming Intercom. Ensure that intercoms are on the same channel. See Operation & Features. Intercom is not getting expected transmission range. Keep antenna vertical. Keep intercom away from trees, metal objects and electrical wiring. Cell phones, cordless phones, or other radio devices may also limit range. Intercom beeps every ten minutes. The battery is low in the intercom. Replace with AA Alkaline batteries or operate it with AC Adapter (not provided). A 9-12 volt, 500mA AC Adapter may be used (center positive polarity on the round plug). Need to clear intercom’s memory. Press and hold Learn button, an initial beep will be heard. Continue to hold until a second beep is heard (about 15 seconds). Ensure other intercoms are not activated during this time. Intercoms in the network that are on will signal during the clearing process. Once memory is clear the intercom can be programmed to a new network. Static and feedback is heard in intercom. The intercoms are too close to each other. A cordless phone, cell phone, or other radio devices can also cause static. Intercom is sending audio while no buttons are pressed. The sending intercom is set to Monitoring Mode or Voice Activation Mode and will activate when sound is heard. It can be taken out of Monitoring Mode by pressing the Talk button. It can be taken out of Voice Activation Mode by setting Dipswitch #1 to DOWN position. See Operation & Features. Troubleshooting Intercom does not function. Check batteries in intercom. If using an AC Adapter ensure that it is plugged in. Ensure intercom is connected to a network. See Programming Intercom. Ensure that intercoms are on the same channel. See Operation & Features. Intercom is not getting expected transmission range. Keep antenna vertical. Keep intercom away from trees, metal objects and electrical wiring. Cell phones, cordless phones, or other radio devices may also limit range. Intercom beeps every ten minutes. The battery is low in the intercom. Replace with AA Alkaline batteries or operate it with AC Adapter (not provided). A 9-12 volt, 500mA AC Adapter may be used (center positive polarity on the round plug). Need to clear intercom’s memory. Press and hold Learn button, an initial beep will be heard. Continue to hold until a second beep is heard (about 15 seconds). Ensure other intercoms are not activated du...
Эта инструкция также подходит к моделям:Проводные телефоны - CARTON INVENTORY RWIS (277.75 kb)