7. Press the C button, then the LCD Screen will display <>. 8. Press C button once more to confirm. To Save Numbers From Caller ID To The Phone Book: 1. Using the or arrow buttons, find the phone number you want to save. 2. Press and Hold the OK button until the last digit of the number is flashing. 3. You can now modify the number and name (see above procedure Review/Modify Number) and save it to your Phone Book. To Dial A Number From The Phone Book: In the hook position, 1. Press the MUTE button to access the Special Feature Menu. 2. Using the or arrow buttons, highlight <>. 3. Press the OK button to confirm. 4. Using the or arrow buttons, scroll to select <>. 5. Press the OK button. 6. Use the arrow buttons to locate the number you wish to dial. 7. Either pick-up the handset, press the SPKR (speakerphone) button or, if you are using either of the hands-free jacks, press the (headset) button. Your CSC50 Phone will automatically dial the number. Recall / Delete One Of the Last 30 Numbers Dialed You can call back the last 30 numbers dialed. To call back one of them, follow instructions below: In the hook position, 1. Press the OK button. 2. The screen will display “DIALED”, the last number dialed, the total of numbers, the date and the hour of record. 3. Using the or arrow buttons, scroll through the numbers and select the number you wish to dial. 4. Lift the handset or press the SPKR button, the number will be automatically dialed. To delete one of telephone numbers, follow instructions below: In the hook position, 1. Press the OK button. 2. The screen will display “DIALED”, the last number dialed, the total of numbers, the date and the hour of record. 3. Using the or arrow buttons, scroll through the numbers and select the number you wish to delete. 4. Press the C button. 5. The Screen will display “DEL?” 6. Press again the C button to confirm. 7. Press the OK button to exit. AUTO ON HOOK When the Auto On Hook feature is ON, Your ClearSounds CSC50 will automatically disconnect the line after 5 - 8 minutes if the phone is left off the hook. This will restore your line to be able to receive another call even if you leave the handset off the base. In the hook position, 1. Press the MUTE button to access the Programming Menu. 2. Using the or arrow buttons, highlight <> then press the OK button to confirm. 3. Using the or arrow buttons, scroll to select <> and press the OK button. 4. Using the arrow buttons, choose <> or <>. 5. Press the OK button. 6. Press the C button twice to exit. Troubleshooting Guide No dial tone 1. Check that all phone cord connections (including the curly cord) and AC Adapter are securely plugged into the telephone & wall jack. 2. Check that the phone is in the correct dialing mode, Touch-Tone / Pulse Setting. 3. Plug another phone into the jack to make sure your phone service is functioning properly. Call will not dial or dials very slowly 1. Check that the phone is in the correct dialing mode, Touch-Tone / Pulse Setting (See page #14). No audible ringer 1. Make sure the ringer is not set to the “OFF” position (See figure #8). 2. Check the volume level of the ringer. 3. You may have too many extensions on your line. Try unplugging a few devices. Having too many telephones /accessories can also create problems such as low ringer volume or impaired quality during calls. No Strobe Ringer and/or bed shaker will not activate 1. Make sure the strobe and/or shaker switch is turned “ON”(See figure #12). 2. Make sure the Bed Shaker is plugged in all the way. 3. Make sure the Bed Shaker is plugged into the correct jack (See figure #11). No amplification 1. Check to see if the AMPLI amplify button is “ON” (See figure #24). The red light should be lit. 2. Check the AC Power Adapter and make sure it is plugged into the wall and into the appropriate jack on the phone. Noise, Static, Interference while using the handset 1. Afilter may be required for homes with DSL line or near Radio towers. There is a red light that continues to flash 1. You have un-reviewed Caller ID / Call Waiting information or missed a call (See page #24). 2. Your Voice Mail account needs to be set-up as Visual Indicator only. Contact your local phone company; if the account is setup as Audible or Audible/Visual indicator, the light will contine to flash after reviewing your voice mail messages. Difficulty storing numbers in memory 1. Make sure you are pressing the correct sequence of buttons for storing numbers. 2. If you are interrupted by the telephone company’s recorded announcement telling you to hang up or by a loud buzzing noise, ignore and continue to store the numbers. Or hang up and store the number without lifting the handset or temporarily disconnect the telephone line until you have programmed in all the numbers. No numbers dialed when memory button is pressed 1. No number stored in that memory button. 2. Make sure phone number was programmed and saved in ...
Войти: