Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
There may be a phone off the hook somewhere in your home. Check that all phones in your home are hung up. 2. Check the Auto On Hook Feature (See page 20). 3. The remote band’s battery is dead or is not installed properly. Check the remote band battery (See page 37). 4. Check the antenna on base. Caller ID information does not show 1. Make sure you are subscribed to Caller ID through your local phone company. 2. Check batteries. No Caller ID information while on a call 1. Make sure your service provides Caller ID Information while you are on a call. This is sometimes known as “Caller ID on Call Waiting” or “Type II Caller ID”. 2. Make sure you have the Caller ID – Caller Waiting feature on this phone set to ON (See page 29). 3. The phone cannot display the information if another phone on the same line is in use. Make sure all extensions are on hook. Cannot dial out of Caller ID 1. Make sure you are subscribed to Caller ID through your local phone company. 2. Make sure your area code is set up properly (See pages 30-31). Maintenance and Care Maintenance and Care The CL600 Emergency Connect Telephone has been designed to give you years of dependable service with a minimum of care. To ensure the utmost in performance, follow these guidelines in caring for your phone: 1. Avoid dropping or knocking the unit. 2. Dust the unit regularly. Unplug your phone and wipe with a soft slightly damp cloth to remove any dirt from it. To avoid damage, NEVER use an abrasive or strong solvent to clean any part of the phone. 3. Keep the phone out of direct sunlight. 4. Avoid placing the phone in extremely humid conditions. 5. Avoid electric shock by keeping the phone away from water (i.e. bathroom, kitchen sink, etc.) Change the Remote Band Battery To replace the battery, lift the remote band, unscrew the three small screws located on the base and lift the cover to access the battery. The Remote Band operates on one alkaline “23A” 12V size cigarette lighter battery. Replace the battery with correct polarity. Replace the cover (See diagram #36). Screws X BAT +- Front Bottom Battery location DIAGRAM #36– Battery Installation NOTE: Be sure to test your Remote Band (See page 18) after changing the battery to assure that your system is operating properly. Specifications Maximum Gain: 42 dB in Wide band (300 to 3400Hz) 52 dB max Low Frequency (Bass 300 Hz) 52 dB max High Frequency (Treble 3400Hz) Maximum Outgoing Gain: +12 dB Dimensions: Size: 10.5” (with Caller ID screen flat) X 8” X 2” Weight: 4.33 lbs Power Requirements: AC Power Adapter: Input: 120 VAC, 60Hz, 26W. Output: 12V DC 1000 mA Batteries: (4) AAA Alkaline batteries (not included) (1) “23A” 12V Alkaline battery (included) FCC Registration Notice THE INFORMATION INFORMING THE USER OF HIS/HER AND THE TELEPHONE COMPANY’S RIGHT AND OBLIGATION IS OUTLINED BELOW. a) This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company. b) All applicable certification jacks Universal Service Order Codes (USOC) for the equipment is provided (i.e. RJ11C) in the package with each piece of approved terminal equipment. c) A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirement adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details. d) The REN is used to determine the number of devices that may be connected to the telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.00). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. [For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by 10 are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.] e) If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your rights to file a complaint with the FCC if you believe it is necessary. f) The telephone company may make changes in its facilities, equipment, operation or procedures that could affect the operation of the equipment. If this happens the telephone company will pro...