Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
Please read this User Guide carefully in order to get the very best results from your telephone. Keep the manual near the telephone for easy reference. Please visit our web site at wwwclearsounds.com to: Register your product, download additional manuals, and review trouble shooting tips. CAUTION: The CSC48 phone is capable of amplifying sounds to a loud volume. It is important to instruct all potential users of its proper operation. It is advised to adjust the volume control to its minimum level when not in use and alert other users that hearing damage can potentially result from misuse. Important Safety Instructions Follow basic safety precautions when using your telephone to reduce the risk of fire, electric shock and injury to persons. • Keep your phone dry; if it gets wet, wipe it immediately. • Handle your phone carefully, DO NOT drop it • Keep your phone away from dust and dirt, and wipe it with a damp cloth occasionally to keep it looking new. Do not use liquid cleaners or aerosol cleaners on the phone. • Do not use this product near water, for example, near a bathtub, washbowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. • Avoid using the telephone during electrical storms. There may be a remote risk of electric shock from lightning. • Do not use the telephone if you suspect a gas leak in the area. Due to the nature of VOIP/Broadband technology results may vary when used with VOIP/Broadband service. location of controls ................................................................................................................ +/- SETM1. M2. M3. 1 Switch Hook 2 Hanging Peg 3 Frequently Called Numbers Quick Reference Guide 4 Flash 5 Redial 6 Receiver Volume Control 7 Boost 8 Boost LED – Lights when booster is activated. 9 Keypad 10 Ringer LED 11 Memory Dial Buttons – Store numbers to dial with one touch 12 Clock Display 13 TIMER 14 SET 15 +/- 16 STORE 17 Tone - Slide to adjust the tone volume for the handset when BOOSTER is activated 18 Ringer OFF LOW HI – Set the ringer volume 19 Telephone Line Jack 20 Battery Compartment SET-UP Connecting the Telephone 1 Connect the curly cord to the handset and to the jack on the left side of the telephone. 2 Place the handset into the cradle. 3 Connect the telephone line cord to the Telephone jack at the rear of the unit. 4 Connect the other end into the telephone wall jack (using adapter plug if required). You will hear a click when the modular plug is correctly in place. Note: Peel the plastic label from your phone’s display before using your phone. Inserting the Battery Before connecting your CSC48 to the telephone line, you should install a AAA battery. The battery is required for the clock to function 1 Open the battery compartment (located on the bottom of the phone) with the small screwdriver or pen. 2 Insert the battery, always ensure that the polarity is correct. 3 Close the battery compartment The battery must be changed when the clock display is no longer visible. NOTE: Before installing or changing the battery make sure that your CSC48 is not connected to the telephone line. Hanging The Phone On The Wall You can place your phone on a flat surface or mount it on a telephone wall plate (not included). 1 To mount using an existing wall plate adapter.* 2 Connect one end of the short phone cord to the telephone wall plate and the other to the telephone 3 Insert the supplied mounting bracket into the slots on the back of the phone and push the bracket up until it clicks. To detach the bracket, simply press the tab and slide down bracket down. 4 Insert the two keyhole slots on the phone with the wall plate and slide the phone down, being careful not to pinch the telephone line, until the phone is secure. 5 Press and lift out the handset holder. Remove the hanging peg (located by the switch hook) by pushing it upwards then rotate the peg 180 degrees, then snap it into place so it will hold the handset in place when the phone is mounted on the wall. *If you do not have an existing wall mount plate adapter they are available at most major electronic and hardware retailers, simply follow the manufacturer’s instructions for installation. Hearing Aid Compatible The CSC48 generates a signal that is picked up by the telecoil of your hearing aid(s). This option is activated by setting your hearing aid to “T” or “MT” position. Flash Many special network services, such as call waiting, require a switch hook signal. Flash provides the electronic equivalent of a switch hook operation. For example if you subscribe to Call Waiting, you can put your 1st caller on hold and answer the 2nd call by pressing the FLASH button. Press FLASH again to return to the first call or alternate between the two. Setting the Clock. Press the SET button beneath the display one time. The hours figure in the display will start to flash. You can now enter the time using the +/- button. To do this, press the +/- button until you see the correct hour in the display...