Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Operation of this equipment in a residential area may cause interference which the user (at his own expense) will be required to correct. This product meets the Electromagnetic Compatibility Directive, 89/336/EEC. ®Audiocom is a registered trademark of Telex Communications, Inc., Burnsville, Minnesota 55337 ®Clear-Com is a registered trademark of Clear-Com Intercom Systems 1 End-User License Agreement for TelexEnd-User License Agreement for TelexSoftware IMPORTANT -Please read this document carefully before using this product. THIS DOCUMENT STATES THE TERMS AND CONDITIONS UPON WHICH TELEX COMMUNICATIONS, INC. (the ‘COMPANY’) OFFERS TO LICENSE THE INSTALLED SOFTWARE OR PROGRAM (the ‘SOFTWARE’) FOR USE WITH THE PRODUCT IN WHICH IT WAS INSTALLED. YOU ARE AGREEING TO BECOME BOUND BY THE TERMS OF THIS AGREEMENT. IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT, DO NOT USE THIS PRODUCT. PROMPTLY RETURN THE PRODUCT TO THE PLACE WHERE YOU OBTAINED IT FOR A FULL REFUND. The installed software as supplied by the Company is licensed, not sold, to you for use only under the terms of this license, and the Company reserves all rights not expressly granted to you. You own the product or other media on or in which the Software is originally or subsequently recorded or fixed, but the Company retains ownership of all copies of the Software itself. 1. License: This license allows you to use the Software for internal purposes only on a single product in which it was installed. 2. Restrictions: (a) You may not market, distribute or transfer copies of the Software to others or electronically transfer or duplicate the Software. YOU MAY NOT REVERSE ENGINEER, DECOMPILE, DISASSEMBLE, MODIFY, ADAPT, TRANSLATE, RENT, LEASE OR LOAN THE SOFTWARE OR CREATE DERIVATIVE WORKS BASED ON THE SOFTWARE OR ANY ACCOMPANYING WRITTEN MATERIALS. (b) The Software and the accompanying written materials are copyrighted. Unauthorized copying of the Software, including portions thereof or the written materials, is expressly forbidden. (c) You understand that the Company may update or revise the Software and in so doing incurs no obligation to furnish such updates to you. 3. Limited Warranty: The Company does not warrant that the operation of the Software will meet your requirements or operate free from error. The Company DISCLAIMS ALL OTHER WARRANTIES AND CONDITIONS EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT OF THIRD PARTY RIGHTS. 4. Limited Liability: The liability of the Company for any claims arising out ot this License based upon the Software, regardless of the form of action, shall not exceed the greater of the license fee for the Software or $50. 38109-709 Rev A 10/97 2 OPERATION OPERATION The BP-2000 belt pack receives power externally, in one of two ways: . Via the intercom channel (similar to the BP-1000) . Via the local-power (pin 2) of the intercom channel connector The BP-1000 belt pack receives power externally, via the intercom channel. Both the BP-2000 and BP-1000 will pass system power through to subsequent belt packs that are “daisy chained” together. INITIAL BP-2000/BP-1000 SETUP The channel termination is initially set for balanced operation, which is compatible with other Audiocom® equipment. If the unit is going to be connected to Clear-Com equipment, one switch and several jumpers must be changed as described in the section on Clear-Com Setup in this manual. The headset microphone type is initially set for single-ended dynamic operation. To change the microphone type to balanced dynamic, refer to Table 2 for the position of J15. To change the headset microphone to an electret type, refer to Table 2 in this manual for the position of switch SW1. If the type requirement of a headset microphone is unknown, the recommended setting is single-ended dynamic. 3 1 234 TALKCALLCHAN1 2 1 234 TALKCALLCHAN1 2 BP-2000 5 67 7 HEADSET LINES 1 34 TALKCALL BP-1000 5 68 8 HEADSET LINES Figure 1. BP-2000 & BP-1000 Connections and Controls 4 EXTERNAL CONNECTIONS & CONTROLS EXTERNAL CONNECTIONS & CONTROLS 1. Volume Control Use this control to adjust the headset listen level. 2. ChanButton and Indicators The Chanbutton (only on the BP-2000) allows the user to select which intercom channel is active. The yellow indicator next to the 1or 2lights to show the active channel. Press the Chanbutton to change the channel selection, the yellow indicator for that channel will light. 3. CallButton and Indicator The Call function allows the user to send or receive signals to other devices on the intercom channel selected. The Callbutton operates in two ways: Call receive: When there is an incoming call signal, the indicator is red. (If Audible Call Alert is enabled, incoming calls will cause beeps in the headset.) On the BP-2000, calls can be received on the selected channel only. Call send: To send a call signal to all stations on a channel, press and hold the Callbutton until a verb...