Оценок - 1, средний балл: 5
(
)
)
|
Фрагмент инструкции
1. Press *24 and enter the four-digit MASTER CODE _ _ _ _ (beep). 2. Enter the area code reference number (0 through 9) _ then press * (beep). 3. Enter # # # # then press * (beep). 4. Repeat steps 2 and 3 to delete additional area codes. 5. Press 0# TOGETHER to end this programming step (beeeeeep). 3.5.9 Display Phone Numbers (1815, 1817 Systems Only) Use this programming sequence to display phone numbers programmed under known directory codes, i.e. if you wanted to see what phone number was programmed under directory code 271. This programming sequence will not allow you to delete phone numbers. 1. Press *06 and enter the four-digit MASTER CODE _ _ _ _ (beep). 2. Enter the directory code (1, 2, 3 or 4 digits depending on what was programmed in 3.5.1) then press * (beep). 3. The phone number programmed under the directory code entered in step 3 will be displayed on the LCD. If C C C C C C C is displayed, this indicates that no phone number has been programmed under the entered directory code. If the first digit is flashing, this is the area code reference code and indicates that the number displayed is a long distance or 10-digit number. 4. To display additional phone numbers press * and repeat step 2. 5. Press 0# TOGETHER to end this programming step (beeeeeep). Text Box: AREA CODES (3.5.3) 1 2 3 4 5 6 7 8 9 0 The PC programmable telephone entry system must be equipped with a MemPLUS chip to program device codes into its memory. Device codes must be five (5) digits in length and are typically card and transmitter codes. Each device code that you enter is assigned to the directory code that you select. Up to 25 device numbers can be entered under a single directory code, up to a maximum of 8,000 for the system. You cannot duplicate device codes. 3.6.1 Programming Device Codes This program sequence enters device (card, transmitter, digital) codes into the system memory. 1. Press *70 and enter the four-digit MASTER CODE _ _ _ _ (beep). 2. Enter the directory code that the device code is to be assigned to (1, 2, 3 or 4 digits depending on what was programmed in 3.5.1) then press * (beep). 3. Enter the five-digit device code _ _ _ _ _ then press * (beep). 4. Repeat steps 2 and 3 to enter additional device codes. 5. Press 0# TOGETHER to end this programming step (beeeeeep). 3.6.2 Deleting Device Codes This program sequence deletes individual device codes. 1. Press *71 and enter the four-digit MASTER CODE _ _ _ _ (beep). 2. Enter the directory code (1, 2, 3 or 4 digits depending on what was programmed in 3.5.1) then press * (beep). 3. Enter the five-digit device code _ _ _ _ _ then press * (beep). 4. Repeat steps 2 and 3 to delete additional device codes. 5. Press 0# TOGETHER to end this programming step (beeeeeep). Text Box: AREA CODES (3.5.3) 1 2 3 4 5 6 7 8 9 0 Four-digit entry codes are entered on the system keypad preceded by # to allow the resident access. Do not confuse four-digit entry codes with a five-digit device code entered from a weigand keypad. 3.7.1 Programming Four-digit Entry Codes 1. Press *02 and enter the four-digit MASTER CODE _ _ _ _ (beep). 2. Enter the directory code (1, 2, 3 or 4 digits depending on what was programmed in 3.5.1) then press * (beep). 3. Enter the four-digit entry code _ _ _ _ then press* (beep). 4. Repeat steps 2 and 3 to enter additional entry codes. 5. Press 0# TOGETHER to end this programming step (beeeeeep). 3.7.2 Delete Four-digit Entry Codes 1. Press *02 and enter the four-digit MASTER CODE _ _ _ _ (beep). 2. Enter the directory code (1, 2, 3 or 4 digits depending on what was programmed in 3.5.1) then press * (beep). 3. Press # # # # *(beep). 4. Repeat steps 2 and 3 to delete more entry codes. 5. Press 0# TOGETHER to end this programming step (beeeeeep). 3.7.3 Entry Code Ranges Four-digit entry codes can be made to activate relay 0, relay 1, or relay 2 or any combination of relays by programming HI and LOW ranges for each relay. Ranges may overlap, which will cause more than one relay to activate if this is desired. For example, if the low boundary for relay 0 and relay 1 is 2000, and the hi boundary is 3000 for relay 0 and 4000 for relay 1, then entry codes between 2000 and 3000 will activate both relays, and entry codes between 3001 and 4000 will only activate relay 1. 1. Press *12 and enter the four-digit MASTER CODE _ _ _ _ (beep). 2. Press 0* to set relay 0, or 1* to set relay 1, or 2* to set relay 2 boundaries. 3. Enter the four-digit low boundary _ _ _ _ then press * (beep). 4. Enter the four-digit high boundary _ _ _ _ then press * (beep). 5. Repeat steps 2, 3, and 4 to set the other relay boundaries (or proceed to step 7). 6. Press 0# TOGETHER to end this programming step (beeeeeep). SECTION 4 – ADJUSTMENTS 4.1 Speaker Volume 1. Open the front of the telephone entry system and locate the speaker volume adjustment. 2. Place a phone call from the telephone entry system to a resident. While they are talking, adjust the speaker volume potentiometer for adequate...
Эта инструкция также подходит к моделям:Проводные телефоны - 1803PC (522.15 kb)
Проводные телефоны - 1815 (522.15 kb)