Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
Your Caller ID can: • store up to 90 call records, including information such as caller’s name, and/or phone number, and the time the call was placed, if available, • alert you when new calls have been received, • display the current time and date, • display the total number of calls received, • display prompts and screen displays in one of three languages: English, French, or Spanish, • alert you when you have messages waiting, if you have a voice mail service from your phone company, and • be used on a desktop or be mounted on a wall. Important! To operate your Caller ID, you must first contact your phone company and order Caller ID service. There is a charge for Caller ID service, which will appear on your monthly phone bill. Caller ID service may not be available in all areas. 1 Introduction New Call Indicator Light Down SET DELREVIEW MSGNEW ® New Message Indicator Light Delete Up Set Battery Compartment Door Wall Mount Wall Mount Phone Jack and Line Jack (Interchangeable) 2 Getting Started To Install the Battery (Not Included) Note: The Caller ID will not function without a battery. 1. Disconnect the telephone line. 2. Lift the battery compartment door on the back of the Caller ID. 3. Install a 9-volt battery. 4. Replace the battery compartment door. To Connect the Telephone Line 1. Connect one end of the telephone cord into one of the jacks on the back of the Caller ID (either jack can be used) and connect its other end into the wall jack. 2. Connect one end of the included telephone cord into the other jack on the Caller ID and connect its other end into your telephone. 3. If desired, use two anchor screws to mount your Caller ID on a wall. 3 Changing the Settings Caution: When you press SET to change a setting, that setting will flash on the screen for about 5 seconds. If you do not adjust the setting and then press SET during this time, the settings will remain unchanged. To Set the Time and Date 1. Press SET until ENTER TIMEappears and the hour is flashing. 2. Use or to adjust the hour. You can also adjust AM and PM on the 12-hour clock while adjusting the hour. Note: When the language is set to English, the clock is a 12-hour clock which can be set to AM or PM. When the language is set to French or Spanish, the clock is a 24-hour clock. 3. To set the minutes, press SET until ENTER TIMEappears and the minutes are flashing and then use or . 4. To set the month, press SET until ENTER DATEappears and the month flashes, and then use or . 5. To set the day, press SET until ENTER DATEappears and the day flashes, and then use or . If you do not want to set the language or area code, wait 5 seconds for the flashing to stop. 4 Changing the Settings To Set the Language and Area Code 1. To set the language of the screen prompts, press SET until IN ENGLISH?appears. 2. Use or to set a language. 3. To set your area code, press SET until ENTER AREA CODEappears and the first digit of the area code flashes. 4. Use or to change the first digit. 5. To change the other digits, press SET until the desired digit flashes and then use or . Note: If your area code has three digits, press SET again when the fourth digit flashes. After you have set the area code, your Caller ID displays the current date and time. AM 4-11 10:30 5 Receiving Calls When the telephone connected to the Caller ID rings, new call information appears between the first and second ring. If you answer before the second ring, the Caller ID will not display any information. When a call is received, the Caller ID displays a call record, which can include, if available, the name of the caller, the caller’s telephone number, and the time that the call was placed. The amount of information displayed depends on the signal sent by your phone company. PM NEW 4-11 1:30 # 609-555-1026 03 JOHN SMITH If the call is from outside your phone company’s area, some of the caller’s information may not be available and UNKNOWN NAME and/or no number may be displayed. The NEW Call Indicator Light will flash for about 15 seconds after a new call is received. If the caller’s name or number is blocked by the caller, that information will not be displayed. 6 Reviewing Calls This Caller ID automatically stores the call information from the last 90 calls. If you have not received any new calls, the Caller ID will display the date, time, and number of total calls, if any. If you have received new calls, the screen will display the appropriate number (ex: 03 NEW CALLS). PM NEW 4-11 4:27 ONE NEW CALL 1. To review your new calls, press repeatedly. 2. To review your old calls, press repeatedly. When you reach the end or top of the list, press the opposite direction key to cycle back through your call records. 7 Reviewing Calls About Message Waiting Your Caller ID can alert you to check your phones messages if you have a voice mail service from your phone company that offers Caller ID signalling. For more information about these services, contact your phone company. When you have a new...