Оценок - 5, средний балл: 4
(
)
)
|
Фрагмент инструкции
For example, in the string: "9;xxxxx" the user dials “9” to get the outside line, listens for the dial tone, and continues to dial the applicable number. The “;” tells the phone to present a second dial tone after the previously dialed digit. “The “xxxxx” in the example tells the phone that a phone number is dialed after the secondary dial tone is audible. You can enter the Secondary Dial Tone string in the Dial Plan using the configuration files or the Aastra Web UI. You use the following parameter in the configuration files to configure a secondary dial tone: • sip dial plan Example sip dial plan: “9;5551313” 41-001160-03, Rev 00, Releaes 2.4 Configuring Operational Features Operational Features Configuring the SIP Local Dial Plan, Dial Plan Terminator, and Digit Timeout Use the following procedures to configure the SIP Local Dial Plan using the configuration files or the Aastra Web UI. Configuration Files For specific parameters you can set in the configuration files, see Appendix A, the section, “SIP Local Dial Plan Settings” on page A-65. 41-001160-03, Rev 00, Releaes 2.4 IP Phone Administrator Guide Operational Features Aastra Web UI 1 Click on Basic Settings->Preferences. 2 In the "Local Dial Plan" field, enter a valid local dial plan (up to 512 alphanumeric characters) for the IP phone. Default is X+#|XX+*. Enter prepended digits or a “;”to present a secondary dial tone if required. Note: If a User enters a dial plan longer than 512 characters, or a parsing error occurs, the phone uses the default dial plan of “x+#|xx+*”. 3 Enable the "Send Dial Plan Terminator" field by checking the check box. (Disable this field by unchecking the box). Default is disabled. 4 In the "Digit Timeout (in seconds)" field, enter a timeout value. This is the length of time, in seconds, he phone waits before dialing. Default is 4 seconds. 5 Click to save your changes. 41-001160-03, Rev 00, Releaes 2.4 Configuring Operational Features Operational Features Park Calls/Pick Up Parked Calls The IP phones (including the 6757i CT handset) have a park and pickup call feature that allows you to park a call and pickup a call when required. There are two ways a user or administrator can configure this feature: • Using a static configuration (globally configures park and pickup) • Using a programmable configuration Note: The IP phones accept both methods of configuration. However, to avoid redundancy, Aastra Telecom recommends you configure either a static configuration or a programmable configuration. The IP phones support the Park/Pickup feature on the Asterisk, BroadWorks, Sylantro, and ININ PBX servers. The following paragraph describes the park and pickup static configuration on the IP phones. Reference For information on configuring the park and pickup programmable configuration (using a key), see “Park/Pick Up Key” on page 5-234. Park/Pickup Static Configuration (9480i, 9480i CT, 6755i, 6757i, 6757i CT only) Using the static method of configuring park and pickup configures these features on a global basis for all IP phones connected in the network. You can use the configuration files or the Aastra Web UI to configure a park/pickup static configuration. In the configuration files, you use the following parameters to statically configure park/pickup: • sprecode: • pickupsprecode: 41-001160-03, Rev 00, Releaes 2.4 IP Phone Administrator Guide Operational Features In the Aastra Web UI, you use the following fields at Basic Settings-> Preferences to configure park/pickup statically: • Park Call • Pickup Call How It displays on the Phone On the IP phone UI, the static configuration method displays the following: • When a call comes in, and you pickup the handset, the default label of "Park" displays on the first screen of the Phone UI. • After pressing the "Park" softkey to park the call, the default label of "Pickup" displays on the first screen of the phone UI. Note: On the 6757i CT handset, pressing I displays the "Park" and "Pickup" labels. The values you enter for the Park/Pickup feature are dependant on your type of server. The following table provides the values you enter for the “sprecode” and “pickupsprecode” parameters (configuration files), or "Park Call" and "Pickup Parked Call" fields (Aastra Web UI). Park/Pickup Call Server Configuration Values Server Park Values* Pickup Values* Aasterisk 70 70 Sylantro *98 *99 BroadWorks *68 *88 ININ PBX callpark pickup *Leave "value" fields blank to disable the park and pickup feature. 41-001160-03, Rev 00, Releaes 2.4 Configuring Operational Features Operational Features Configuring Park /Pickup using Static Configuration (9480i, 9480i CT, 6755i, 6757i, 6757i CT only) Use the following procedures to configure the Park/Pickup call feature using the static configuration method. Note: Aastra recommends you configure either the static or the programmable configuration, but not both. Configuration Files For specific parameters you can set in the configuration files, see Appendix A, the s...
Эта инструкция также подходит к моделям:Проводные телефоны - 9143i Series (14.11 mb)
Проводные телефоны - 9480i Series (14.11 mb)