Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
While the batteries are being charged, the level shown will keep changing. Outside call You are connected to an outside call. Intercom call You are connected to an intercom call. Phone book Show the names and numbers of stored record. Mute Your handset's microphone is muted. Up and down arrows To browse through the programming menu for more options. Speakerphone Your handset’s loudspeaker is on. Signal level Shows the strength of the signal between the handset and base unit, and flashes when you are out of range of the base unit, when the level is low, or the symbol is flashing, move closer to base unit. Missed call You have new missed call. The Handset and Base Unit MENU/ Mute button Press to turn the speakerphone ON/OFF Call button Press to begin and answer the call UP/DOWN button In standby mode, press to show phonebook list; Press during programming to move through the menu. Press during a call to change the volume in the earpiece. Press to enter menu mode and enter sub-menu. Use the key " " to lock or unlock the keypad. Press during a call to mute the microphone Speakerphone button In standby mode, press to enter phonebook mode. Press to confirm selection. You can activate Recall function if your phone is connected to a PABX, or if you use Select Services. Press to transfer an outside call to another phone. Press and hold (2-3 seconds) to switch the handset on and off. Press during programming to go back to the previous option, or to clear digits one by one from the display. Press to end the call. IN USE light The IN USE light comes on when you have a connection to the telephone line. INT button Press to make an intercom call (if you have more than one handset) PHONEBOOK/OK/Recall button Clear / On-Off /End button HANDSET LOCATOR button Press this to make the handset ring, if you cannot remember where you put it. Press it again to stop the handset ringing. Before you can use the handset to make calls for the first time, you will need to fit and fully charge the battery for 15 hours. Setting up your telephone Connection and conditions for use You can connect your phone to a direct exchange line (DEL), a line connected to a local exchange, with its own phone number; to an extension socket connected to a DEL; or to an extension on an approved compatible PBX. Do not connect your phone as an extension to a payphone. How many phones can you connect? The ringer equivalence numbers (RENs) of all instruments (phones, fax machines, etc.) connected to an exchange line must not add up to more than 4, otherwise, one or more of them may not ring and/or answer calls correctly. Phone has a REN of 1, and most other telephones have a REN of 1 unless marked otherwise. Radio signals between handset and base unit To use your handset and base unit together, you must be able to establish a radio link between them. Be aware that: . Sitting the base unit as high as possible will give better results, in a two-storey house, the best position may be on the first-floor landing. . Any large metal object, like a fridge, a mirror or a filing cabinet, between the handset and base unit may block the radio signal. . Other solid structures, like walls, may reduce the signal strength. Choosing a site for the base unit The base unit should be placed on a level surface, in a position where: . The mains adapter plug will reach a 230-V AC switched mains supply socket; never try to lengthen the mains power cable. . The telephone cable will reach your telephone line socket or extension socket. . It is not close to another telephone, this can cause radio interference. . It is not close to a sink, bath or shower, or anywhere else where it might get wet. . It is not close to other electrical equipment, fridges, washing machines, microwave ovens, TVs, fluorescent lights, etc. Installation 1. Choose a suitable site for the handset unit Make sure it is not near to another telephone, nor to other electrical equipment. 2. Plug the mains power lead into the power jack on the base unit and plug the telephone line cord into the telephone port. 3. Plug the mains adapter into a 230V AC, 50 Hz mains socket, with the switch on the socket set to OFF Note: The illustration of adaptor may vary from country to country. 4. Switch on mains power at the socket 5. Fit the battery in the handset(s) Insert the battery pack as shown. Fit the battery compartment cover, Sliding it until it clicks firmly into position. 6. Connect the base unit to the telephone line Important safety information This equipment is not designed for making emergency calls in the event of a power failure. Alternative arrangements should be made for access to emergency services. (This means that you should also have a basic phone that does not need mains power, connected to your line so that you can make calls during a power failure) People with a heart pacemaker should consult their doctor before using the telephone. If you wear a hearing aid, you should note your phone works by transmitting rad...