Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
.. .. .. 20 Reviewing Call Information .. .. ... .. .. ... .. ... .. ... .. ... .. .. ... .. ... .. ... .. .. ... .. ... .. ... .. .. .. 20 Deleting Call Records .. ... .. ... .. ... .. .. ... .. ... .. ... .. ... .. .. ... .. ... .. ... .. .. ... .. ... .. ... .. .. .. 24 Care and Maintenance .. .. .. ... .. ... .. ... .. .. ... .. ... .. ... .. ... .. .. ... .. ... .. ... .. .. ... .. ... .. ... .. .. .. 25 Lightning . .. .. ... .. ... .. ... .. .. ... .. ... .. ... .. .. ... .. ... .. ... .. ... .. .. ... .. ... .. ... .. .. ... .. ... .. ... .. .. .. 27 8 9 INSTALLING BATTERIES The System 240 is powered by three AAA batteries. For the longest operation, we recommend you use alkaline batteries (RadioShack Cat. No. 23-555). Follow these steps to install the batteries. Note: If you are replacing the batteries, unplug the module from the phone line. 1. Press down and slide off the battery compartment cover in the direction of the arrow. 2. Place the batteries in the compartment, following the correct polarity (+ and –) as marked inside the compartment. The call indicator on the front of the module lights and a test screen appears. The indicator turns off when the total memory capacity appears briefly. Then the screen goes blank. 3. Replace the cover. + AAA15V AAA15V + + AAA15V + + + 43-962A.fm Page 9 Monday, August 16, 1999 3:33 PM 4 3 -9 62 A . f m P a g e 10 M o nda y , A u gu s t 16 , 1 9 9 9 3 : 33 P M When the battery low indicator ( ) appears in the top left corner of the display or the display dims, replace the batteries. Cautions: • Once you remove the batteries from the Caller ID module, you have 7 seconds to install new batteries without losing saved information. • Do not press any buttons after you remove the batteries. Doing so can delete the information stored in the module. • Do not mix old and new batteries, different types of batteries ( standard, alkaline, or rechargeable) , or rechargeable batteries of different capacities. 10 43-962A. fm Page 11 Monday, August 16, 1999 3: 33 PM CONNECTING TO THE PHONE LINE CONNECTING TO A SINGLE LINE The Caller ID module connects to the phone line using a modular telephone- line connector. If your phone line does not have this type of jack, you can update the wiring yourself using necessary adapters available at your local RadioShack store. Or, you can have the telephone company update your telephone wiring for you. Note: The USOC number of the jack to be installed is RJ11C. 11 43-962A. fm Page 12 Monday, August 16, 1999 3: 33 PM Follow these steps to connect the module to the phone line. REVIEW 1. Unplug the phone’s cord from the phone line jack and plug this cord into the module’s PHONE jack. 2. Plug one end of the supplied modular cord into the module’s WALL jack. 3. Plug the other end of the supplied modular cord into the phone line jack. 12 43-962A. fm Page 13 Monday, August 16, 1999 3: 33 PM CONNECTING TO A TWO-LINE, THREE-WAY JACK You can connect the module to a two- line phone using a two- line, three- way jack ( Cat. No. 279- 402) . The module only shows information about calls received on the line to which it is connected. Follow these steps to connect the module to a two- line phone. D E L E T E R E V IE W 1. Unplug the phone’s cord from the phone line jack, then plug the two- line, three- way jack into the phone line jack. 13 14 2. Plug the phone’s cord into the L1 + L2 jack on the adapter. 3. Plug one end of the supplied modular cord into the module’s WALL jack. 4. Plug the other end of the modular cord into either the L1 or L2 jack on the adapter, depending on which line’s calls you want to monitor. Note: You can also connect two modules (one module for each line) as shown here. Each module shows information for the line you connect it to. Simply plug the other module into the remaining jack (L1 or L2) on the adapter. DELETE REVIEW DELETE REVIEW 43-962A.fm Page 14 Monday, August 16, 1999 3:33 PM 15 CONNECTING TO AN ANSWERING MACHINE 1. Unplug the answering machine’s cord from the phone line jack, then plug the cord into the module’s PHONE jack. 2. Plug one end of the supplied phone cord into the WALL jack on the module. Then plug the other end of the cord into the phone line jack. 3. Set the answering machine to answer calls after at least two rings. Note: If you connect a telephone answering machine to the same line as the Caller ID System 240, you must set the answering machine to answer in two or more rings in order to receive the Caller ID information. DELETE REVIEW 43-962A.fm Page 15 Monday, August 16, 1999 3:33 PM 4 3 -9 62 A . f m P a g e 16 M o nda y , A u gu s t 16 , 1 9 9 9 3 : 33 P M MOUNTING THE MODULE You can place the module on a desktop or table, or mount it on a wall. To mount the System 240 on a wall, you need two wood screws ( not supplied) . 1. Use the bracket as a template to mark the screw locations, then drill two Screw Holes holes into the wall. 2. Secure the bracket to the wall by threading two screws into the bracket...