Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
Follow these steps to install batteries. 1. Use a Phillips screwdriver to remove the screws on the battery compartment cover, then lift and remove the cover. 2. Place the batteries in the compartment as indicated by the polarity symbols (+ and –) marked inside. 3. Replace the cover and secure it with the screws. ID TO LEARN appears. When the display dims or appears, replace the batteries. Preparation 9 43-940.fm Page 10 Tuesday, April 25, 2000 1:04 PM Warning: Dispose of old batteries promptly and properly. Do not burn or bury them. Caution: If you do not plan to use the receiver with batteries for a month, remove the batteries. Batteries can leak chemicals that can destroy electronic parts. Using AC Power You can also power the system’s receiver using an optional 9V, 200-mA AC adapter and a size M AdaptaplugTM adapter (available at your local RadioShack store). Cautions: ! You must use a Class 2 power source that supplies 9V DC and delivers at least 200 mA. Its center tip must be set to positive and its plug must fit the receiver's DC 9V jack. Using an adapter that does not meet these specifications could damage the receiver or the adapter. • Always connect the AC adapter to the receiver before you connect it to AC power. When you finish, disconnect the adapter from AC power before you disconnect it from the receiver. 1. Insert the Adaptaplug into the adapter’s cord so it reads TIP +. 2. Insert the Adaptaplug into the receiver’s DC 9V jack. 3. Plug the adapter into a standard AC outlet. IDTOLEARN appears. 10 Preparation 43-940.fm Page 11 Tuesday, April 25, 2000 1:04 PM CONNECTING THE SYSTEM The system’s transmitter connects to any modular phone jack and your phone. You can also connect it to an answering machine. Note: To insure proper operation, always connect the system’s transmitter directly to a wall jack. Connecting to a Single-Line Phone 1. Disconnect the line cord from your phone and plug it into the transmitter’s LINE-IN jack. Be LINE-IN LINE-OUT sure the other end of the line cord is directly connected to a wall jack. 2. Plug one end of the supplied line cord into the transmitter’s LINE-OUT jack. 3. Plug the other end of the cord into the phone’s jack. Connecting to an Answering Machine 1. Plug a telephone line cord from the phone line into the transmitter’s LINE-IN jack. Be sure the other end of the line cord is directly connected to a wall jack. 2. Plug one end of the supplied line cord into the transmitter’s LINE-OUT jack and plug the cord’s other end into the answering machine’s line jack. Preparation 11 43-940.fm Page 12 Tuesday, April 25, 2000 1:04 PM 3. Plug a third line cord into the answering machine’s phone jack and the telephone’s modular jack. 4. Set your answering machine to answer after two or more rings. This gives the system time to record the call information that the phone company sends between the first and second rings. SETTING THE SYSTEM’S IDENTIFICATION CODE You can install multiple receivers. Each receiver that you install must be set with the same identification code as the transmitter. Follow these steps to set the code. Note: If you hold down PAGE for 5 seconds or longer, the transmitter’s identification code changes. Be sure to set all receivers to the new code. 1. Place the receiver next to the transmitter. 2. Hold down SET on the receiver for about 5 seconds. WAITING ID appears. 3. Press PAGE on the transmitter within 10 seconds after WAITING ID appears. This sends the transmitter identification code to the receiver. The receiver beeps and ID SETappears, indicating that the ID code is set. CHECKING THE RANGE 1. Place the receiver at the desired location. 2. Press PAGE on the transmitter. 12 Preparation 43-940.fm Page 13 Tuesday, April 25, 2000 1:04 PM If the receiver is within the range, it beeps and PAGED appears for 30 seconds. If PAGED does not appear, move the receiver closer to the transmitter and press PAGE again. If it still does not beep, repeat the steps under “Setting the System’s Identification Code” on Page 12 to verify that the identification code is properly set. The receiver checks the range every three hours. If the receiver is out of the range of the transmitter, OUTOFRANGE appears. Move the receiver closer to the transmitter and press PAGE to check the range again. Note: The transmitter can support an unlimited number of receivers. The distance between receivers should be 2 feet or more to avoid interference. SETTING THE DISPLAY CONTRAST, ALERT TONE, AND CLOCK DISPLAY FORMAT 1. Hold down SET and 6 9999DOWN for about 5 seconds until SETTINGSappears. 2. Press 6 9999DOWN to set the display contrast (the default setting is 2). 3. Repeatedly press SET to select the contrast level (1–4), then press 6 9999DOWN. The current tone setting appears. (The default setting is BEEPOFF.) 4. Press SET to toggle between BEEP ON and BEEP OFF, then press 6 9999DOWN. The display shows the current clock format setting (the default setting is a 12-hour format). Preparation 1...