Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
Doing so could erase all stored information. 10 43-933.fm Page 11 Monday, August 16, 1999 2:59 PM • When replacing the batteries, have fresh ones on hand before you begin. If you do not install the new batteries within about 2 minutes after removing the old ones, you will lose all the information stored in the system. 1. Make sure the system is unplugged from the telephone line and AC power. 2. If you are replacing the batteries, unplug both modular line cords from the back of the system. 3. Use a Phillips screwdriver to remove the screw in the battery compartment cover. 4. Slide the battery compartment cover in the direction of the (illus) arrow, then lift open the cover. Caution: The battery compartment cover is attached to the system. Do not try to remove it completely. 5. Put four fresh AAA batteries into the compartment as indicated by the polarity symbols (illus) (+ and –) marked inside. 6. Close the cover and secure it with the screw. If you are replacing the batteries, reconnect the phone line, AC adapter, and the phone. 11 43-933.fm Page 12 Monday, August 16, 1999 2:59 PM When BATTappears or the display dims, replace the batteries. Cautions: • Always remove old or weak batteries. Batteries can leak chemicals that can damage your system. • Dispose of dead batteries promptly and properly. Do not bury or burn them. CONNECTING THE AC ADAPTER (illus) To power the system, plug the adapter’s barrel plug into the 9V DC 200mA jack on the back of the system. Then connect the other end of the adapter to a standard AC outlet. Caution: The supplied adapter was designed specifically for your system. Use only the supplied adapter. 12 43-933.fm Page 13 Monday, August 16, 1999 2:59 PM CONNECTING THE SYSTEM The System 933 connects to any modular phone jack and your phone. You can also connect it to an answering machine. Connecting to a Single-Line Phone (illus) 1. Disconnect the telephone line cord from the phone and plug it into the system’s LINE jack. 2. Plug one end of the supplied line cord into the system’s PHONE jack. 3. Plug the other end of the cord into the phone’s jack. 13 43-933.fm Page 14 Monday, August 16, 1999 2:59 PM Connecting to a Two-Line Phone To record information about calls received on a two-line phone, you can connect two System 933s using a triplex adapter such as Cat. No. 279-402 (not supplied). Each system only records information about calls received on the line to which it is connected. Follow these steps to connect two System 933s to a two-line phone. (illus) 1. Disconnect the telephone line cord from the modular phone jack (on the wall) and plug it into L1 + L2 on the triplex adapter. 2. Plug the triplex adapter into the modular phone jack. 3. Plug one end of the supplied line cord into the TO LINE jack on one of the systems. 4. Plug the other end of the cord into either L1 or L2 on the triplex adapter. 5. Repeat Steps 3 and 4 to connect another system to the remaining open jack (L1 or L2) on the triplex adapter. 14 43-933.fm Page 15 Monday, August 16, 1999 2:59 PM Connecting to an Answering Machine (illus) 1. Plug a telephone line cord into the modular jack and plug it into the system’s TO LINE jack. 2. Plug one end of the supplied line cord into the system’s TO PHONE jack and plug the cord’s other end into the answering machine’s jack. 3. Plug a third telephone line cord into the answering machine and the phone. 4. Set your answering machine to answer after two or more rings. This gives the System 933 time to record the call information that the phone company sends between the first and second rings. MOUNTING THE SYSTEM You can place the system directly on a desk, shelf, or table by itself or attach the supplied mounting bracket if you want the system to sit up at an angle. Or, you can use the bracket to mount the system on a wall. 15 43-933.fm Page 16 Monday, August 16, 1999 2:59 PM Attaching the Mounting Bracket (illus) 1. Align the keyhole slots on the bottom of the system with the hooks on the mounting bracket. 2. Gently push the system down on the bracket to secure it. If you are placing the system on a desk, shelf, or table, pull out the stand on the back of the bracket until it clicks. To remove the system from the bracket, press up from the bottom of the system until it snaps off the bracket. Mounting on a Wall To mount the system on the wall, you need two screws (not supplied) with heads larger than the keyhole slots on the back of the mounting bracket. Follow these steps to mount the system on a wall. 1. Using the keyholes in the supplied mounting bracket as a template, mark the mounting screw locations on the wall. 2. Drill a hole in the wall at each marked location. 16 43-933.fm Page 17 Monday, August 16, 1999 2:59 PM 3. Thread a screw through each hole, letting the head extend 1/8 inch from the wall. 4. Attach the mounting bracket to the system (see “Attaching the Mounting Bracket“ on Page x). 5. Route the phone line cords and AC adapter cord through the slots on the back...