Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
(The Caller ID information, however, stays stored in the CID-927’s memory.) 1. Use a Phillips screwdriver to remove the screw on the battery compartment cover. 2. Press in the tab on the battery compartment cover and lift off the cover. 3. Put the batteries in the compartment as indicated by the polarity symbols (+ and –) marked inside. 4. Replace the cover and secure it with the screw. Once you install the batteries, 12:00AM 1/01 appears. The telephone company sends the correct time with each incoming call, so the correct date and time are automatically set when the CID-927 receives its first call. When flashes in the upper right corner of the display or the display dims, replace batteries. Cautions: • Always remove old or weak batteries. Batteries can leak chemicals that can destroy electronic parts. • Dispose of old batteries promptly and properly. Do not burn or bury them. 43-927.fm Page 6 Thursday, June 24, 1999 9:36 AM 43-927.fm Page 7 Thursday, June 24, 1999 9:36 AM CONNECTING THE PHONE Plug one end of the supplied modular cord into the jack on the back of the CID-927. Then plug the other end of the cord into the modular phone line jack. CONNECTING THE HANDSET Plug one end of the supplied coiled modular cord into the jack on the left side of the phone and the other end into the jack on the handset. Then place the handset on the base. SETTING THE DIALING MODE Set TONE/PULSE on the back of the base for the type of service you have. If you are not sure which type you have, do this test. 1. Be sure TONE/PULSE is set to TONE. TONE/PULSE 2. Lift the handset and listen for the dial tone. 3. Press any number except 0. Note: If your phone system requires that you enter an access code (9, for example) before you dial an outside number, do not press that number. If the dial tone stops, you have touch- tone service. Leave TONE/PULSE set to TONE. If the dial tone continues, you have pulse service. Set TONE/PULSE to PULSE. SETTING THE RINGER’S VOLUME Set RINGER OFF/LO/HI on the back of the base to LO for a normal ringer volume, or HI for a louder ring. RINGER OFF/LO/HI 7 43-927.fm Page 8 Thursday, June 24, 1999 9:36 AM If you do not want the ringer to sound, set RINGER OFF/LO/HI to OFF. With the ringer off, you can still make calls (and answer calls if you hear another phone on the same line ringing). SETTING THE DISPLAY LANGUAGE The CID-927 is preset to show Caller ID messages in English. Follow these steps to change the language to French or Spanish. Note: If you do not finish a step within 20 seconds and the phone exits setup, or if you make a mistake, start again at Step 1. STORE 1. Press STORE. PROGRAM MODE appears. 2. Press REVIEW . SET LANGUAGE then 1=EN 2=SP 3=FR appears. 3. Press: • 1 to select English • 2 to select Spanish • 3 to select French The CID-927 beeps once, then the current time display returns. SETTING THE DATE AND TIME Your phone company sends the date and time with each incoming call if you subscribe to Caller ID service. Or, follow these steps to set the date and time. Note: If you make a mistake, simply start again at Step 1. 1. Press STORE. PROGRAM MODE appears. 2. Press REVIEW . -:- -/- - with the date cursor flashing and SET DATE appear. 3. Enter the desired date using number keys. SET TIME appears and the hour cursor flashes. 4. Enter the desired time. =AM #=PM appears. 5. Press to select AM or # to select PM. The phone beeps and the set time display returns. ADJUSTING THE DISPLAY CONTRAST Repeatedly press CONTRAST on the back of the phone to adjust the display contrast. The CID-927 beeps once then the current time display returns. CONTRAST 8 43-927.fm Page 9 Thursday, June 24, 1999 9:36 AM PHONE OPERATION USING REDIAL The redial memory holds up to 32 digits, so it can store both long-distance and local numbers. To redial the last number, lift the handset then press REDIAL. REDIAL Notes: • The redial memory only stores the last 32 digits of any number dialed. • The redial memory does not store a flash entry but stores any digits you press after FLASH (see “Using Flash”). USING FLASH FLASH performs the electronic equivalent of a switchhook operation for special services, such as Call Waiting. FLASH For example, if you have Call Waiting, press FLASH to answer an incoming call without disconnecting the current call. Press FLASH again to return to the first call. Note: If you do not have any special phone services, pressing FLASH might disconnect the current call. USING TONE SERVICES ON A PULSE LINE Some special services, such as bank- by-phone, require tone signals. If you have pulse service, follow these steps to use those special services. 1. Be sure TONE/PULSE is set to PULSE. 2. Call the service. 3. When the service answers, press . Any additional numbers you dial are sent as tone signals. STORING AND DIALING PRIORITY NUMBERS You can store emergency phone numbers or the phone numbers you call most frequently in the three priority memory locations for one-touch dialing. Each memory loc...