Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
2. Follow steps 1 and 2 above. 3. Then press down and slide the bracket upward until the tabs snap into place. 4. Plug one end of the telephone cable into the TEL. LINE jack at the back of the base. 5. Plug the other end of the telephone cable into the telephone socket, then align the base’s keyhole slots with the screws and slide the phone downward to secure it. fig B 5 4 Basic settings 1. After installing the batteries, the display should flash the word ENGLISH”. If not press and hold for approximately 4 seconds. 2. Select the desired language using or . Press DELETE button. 3. Select the desired contrast setting (2=Default) using or . Press DELETE button. 4. Set the hour (00-23) using or . Press DELETE button. 5. Set the minute using or . Press DELETE button. 6. Set the day using or . Press DELETE button. 7. Set the month using or . Press DELETE button. 4.1 Display (LCD) Contrast/Time Setting If you wish to change the language, LCD contrast or time setting at a later date, press and hold or button for approximately 4 seconds and repeat steps 2-8 above. 4.2 Select country version 1. For New Zealand Select Recall = 600 on the switch on the rear side of the unit, New Zealand Recall/flash time is 600ms, the unit is now set up to insert 0/00 when receiving CID log in accordance with Telecom NZ requirements.There may be some incoming international calls which result in number lengths of less than 10 digits, but these are expected to be in the minority.Typical examples are those from the Pacific Islands. These numbers will be displayed as national numbers. Numbers longer than 14 digits will not be displayed correctly and Dial back function should not be used. Or for Australia Select Recall = 100. 2. Lift and replace the handset to initialize. NOTE: If the switch is in the incorrect position Caller ID and the recall function will not operate correctly. 5. Operation When the telephone is not in use, the date and time, number of new and total number of calls stored in the Caller ID memory will be shown in the display. The display will show the caller number (and name if available). 6 5.1 Making a call 1. Pick up the handset or press SPEAKER button (the speaker LED will light) and wait for a dial tone. 2. Dial the number you wish to call. The display will show the number that you are dialling. If you dial a number over 14 digits long, it will show the last 14 digits only. 3. When you have completed your call, hang up the handset or press SPEAKER button again to release the telephone line. It is possible to switch from a handset to speakerphone conversation by pressing the SPEAKER button and picking up or hanging up the handset accordingly. Pre Dialing a Call 1. Dial the number you wish to call .To correct a number press the DELETE button for each incorrect digit. 2. Pick up the handset or press the SPEAKER button. 5.2 Receiving a Call When you receive a call, the telephone rings, the Ringer LED flashes, and the display shows the CALL # and the caller telephone number (with caller ID service activated). This feature allows you to decide to pick up the phone or not depending on who is calling. If you want to talk to the caller: 1. Pick up the handset or press SPEAKER button to answer the call. 2. At the end of the call, return the handset to the cradle or press SPEAKER button again. 5.3 Redial function If a number that you have dialled is engaged or you were unable to get through to anybody. The last number dialled will be saved in the telephone automatically. To use the redial facility, proceed as follows: 1. Lift the handset or press SPEAKER button . 2. Press the REDIAL button.The last saved redial number will now be dialled. 5.4 Pause If needed for phone banking or behind a PBX system.You can insert a 3.6 seconds pause while dialing or storing a number into MEM. Press REDIAL button at the desired point in number to insert a pause. 5.5 Recall and call waiting The recall button timing can be switched between either 100ms (AUS) / 600ms (NZ), using the Recall switch located on the rear side of the handset. 7 5.6 How To Turn on Telstra call waiting (Australia) You can use the RECALL button to answer a second call while you are on the phone. However this service will need to be turned on. For example to turn on Telstra’s Call Waiting service: 1. Lift the handset and wait for dial tone then Press *43#. 2. You will hear the service message and then hang up. Take two different calls at the same time During a call, you will hear two loud beeps periodically to notify you of another incoming call. If you wish to answer this call 1. Press Recall button listen for dial tone then Press 2 to put the current call on hold and talk with the second caller. 2. Subsequent presses of Recall button listen for dial tone then Press 2 will toggle you between these 2 callers. 5.7 Call Timer Immediately after dialling a telephone number a call timer will be shown on the display.The timer is a simple way to help you keep track of how long the ...