Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
Keep this installation manual at hand for later reference. Read User's Guide and Safety Instructions of your projector and follow the instructions in these documents. Explanation of Symbols The warning marks shown below are used throughout this installation manual to prevent personal injury or property damage. Make sure you understand these warnings when reading this installation manual. Warning This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling. Caution This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling. Symbol indicating an action that must not be done Symbol indicating an action that should be done Safety Precautions for Installation Warning The mount mass is approximately 10 kg (22 lb). Handle the mount carefully when transporting or carrying to prevent injury. The installation work should be performed by specialists who have special technical knowledge and ability. Incomplete or incorrect installation could cause the mount to fall and cause personal injury or property damage. Contact the customer support office listed on Epson Projector Contact List in the User's Guide of your projector when installing the mount. Turn off the projector when installing the mount. Working with the projector turned on could cause fire or electric shock. Handle the power cable carefully. Incorrect handling could cause fire or electric shock. Observe the following precautions when handling: • Do not handle the plug with wet hands. • Do not use a power cable that is damaged or modified. • Do not pull the power cable with too much force when routing the cable through the arm unit. Do not put any thing heavier than the projector on the arm unit. Doing so could cause the arm unit to fall and cause personal injury or property damage. When you set the projector on a wall with this mount, the wall requires enough strength to hold the projector and this mount. A wall of reinforced concrete or steel skeleton construction is recommended. Confirm the mass of the projector and the mount, and keep the strength of the wall. If the wall does not have enough strength, reinforce the wall before installing. Do not install the mount in places where it might be subjected to vibration or shock. Vibration or shock could cause damage to the projector or mounting surface. It could also cause the mount or the projector to fall and cause personal injury or property damage. Install the mount firmly to hold the mass of the projector and the mount, and to resist horizontal vibration. Use M8 nuts and bolts. Nuts and bolts smaller than M8 could cause the mount to fall. Epson takes no responsibility for any damage or injury caused by incorrect installing. The installation work should be performed by at least two qualified service personnel. If you need to loosen any screws while installing, be careful not to drop the mount. If the mount or the projector falls down, it could cause personal injury or property damage. Warning Do not use the mount when damaged. Doing so could cause the arm unit to fall and cause personal injury or property damage. Never modify the mount. Do not hang onto the mount. Or do not hang a heavy object on the mount. It is dangerous if the mount falls down. If the projector or the arm unit falls down, it could cause personal injury or property damage. Stop using this mount and contact the customer support office listed on Epson Projector Contact List in the User's Guide of your projector when the following trouble occurs. • The mount is dropped and/or damaged during installation. • The arm is about to fall. If you use adhesives to prevent the screws from loosening or things such as lubricants or oils on the mount, the case may crack and this could cause the projector to fall. It could cause personal injury or property damage. Do not use adhesives, lubricants or oils to install or adjust the mount. Tighten all screws firmly after adjustment. If the screws are not properly tightened, it could cause the projector to fall and cause personal injury or property damage. Never loosen the bolts and nuts after installation. Confirm that the screws have not become loosened on a regular basis. If you find any loose, tighten the screws firmly. If the screws are not properly tightened, it could cause the projector to fall and cause personal injury or property damage. Caution Do not use in places where the humidity is high. High humidity could cause fire or electric shock. Do not install at place where there is a lot of dust, or a place where it may come into contact with smoke or steam such as near cooking appliances or a humidifier. These could cause fire or electric shock. Do not change the angle of this mount or the projector with excess force. Too much force could damage the mount and could cause personal injury or property damage. Before Usage This product is for mounting an Ep...