Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
Press again to release the Freeze function. ZOOM W/T buttons To adjust the size of the image. Press the ZOOM T button to enlarge the image. Press the ZOOM W button to widen the area to be captured. • These buttons are also used for menu operations from the operation panel. FOCUS 8 / 9 buttons Press to focus on the document. For automatic focusing, press both buttons simultaneously. • These buttons are also used for menu operations from the operation panel. MENU button Press to turn the menu display on/off. REVERSE button, NEGA and BLUE indicators For a negative image, press the button. Each time you press the button, the display changes in the sequence: Normal H Black & White Reversal (NEGA indicator lights) H Blue display (BLUE indicator lights) H Normal, and so on. BRIGHTNESS buttons Press to adjust the brightness of the screen. POWER indicator It lights when the power is on. E-ZOOM button/indicator Press the button to activate the electronic zoom function. The indicator lights, and the image is enlarged 2 or 4 times. When you press the button again, the function is deactivated, and the indicator goes dark. TONE button/indicator Press the button to sharpen the image. The indicator lights. When you press the button again, the TONE function is deactivated and the indicator goes dark. Using the menu, fine adjustment in 5 steps can be made. LIGHTS button/UPPER and LOWER indicators Press the button to light the fluorescent lamps. Each time you press the button, the illumination changes in the sequence: Upper lamps on (UPPER indicator lights) H Lower lamps on (LOWER indicator lights) H Both off, and so on. Operation panel 2 POWER switch • The Freeze function is valid only for the monitor or projector screen connected to the RGB connector of this unit. • This button is also used for menu operations from the operation panel. Shooting a Document Shooting a Document 1 Perform connections. Connect a monitor or projector to the RGB connector on the rear of this unit. For details, refer to page 13 of the User’s Manual. 2 Turn on the unit. Press the POWER switch down to the . side. POWER 6 Place the material on the document stage. approx. Top Bottom 297 mm . 420 mm width wide 210 mm . 297 mm upright 7 Adjust the image size. Press the ZOOM W or T button. When you hold the button pressed, the image size changes continuously. 3 Turn on the monitor or projector. For details, refer to the operation manual for the connected equipment. 4 Perform the input selection on the monitor or projector. Set it so that the picture from this unit is displayed. 5 Turn on the lamps. ZOOM T button Press to enlarge the Press the LIGHTS button. image (max. 6 times). Pressing the button switches the overhead lighting to the lower built-in light. L For opaque material Use the overhead lighting. L For transparent material Use the built-in light under the document stage. ZOOM W T ZOOM W button Press to widen the area to be captured. 8 Adjust the focus. Press the FOCUS 8 and 9 buttons simultaneously. The focus is adjusted automatically. For fine adjustment, lightly tap the FOCUS 8 or 9 button until correct focus is obtained. FOCUS AF 9 Adjust the brightness. Press the BRIGHTNESS + or – button. The image +– BRIGHTNESS The image becomes dark. becomes bright. L Using the Freeze function When changing the materials, you can eliminate operator’s hands being seen on-screen. 1 Press the FREEZE button. Press the button before removing the material. The image will be frozen on the screen. 2 Change the material. The original image stays on the screen. 3 Press the FREEZE button again. The Freeze function is deactivated, and the image of the new material appears on the screen. L Using the Pen function You can draw lines or circles using a mouse for smooth presentations. 1 Display the PC Card menu. Right-click on the area in the lower four-fifths of the screen. 2 Select the pen colour. Left-click on the Red-, Green-, or Blue-Pen button. The pointer changes to a pen icon of the selected colour. 3 Draw a line using the pen icon. Drag the pen icon (move it while holding the left mouse button pressed). • The lines drawn with the Pen function will disappear when another image on the PC card is displayed. • To deactivate the Pen function, click the right mouse button. • For details on PC cards, refer to pages 33 to 37 of the User’s Manual. L For a clear image Press the TONE button. The contrast of the image is emphasized, making the image clear. L Using the electronic zoom Press the E-ZOOM button. The electronic zoom function is activated, and the E-ZOOM indicator lights. The image size becomes two or four times that adjusted with the ZOOM W/T buttons. Red-Pen button Green-Pen button Blue-Pen button You can draw a line on the screen as desired. Using Menus Using Menus Further detailed adjustments and settings can be made using the menus. There are two methods for menu operations; using the operation panel and using a mouse. The method using a mouse is discussed here...