Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
All rights reserved. APC is a registered trademark of American Power Conversion All other trademarks are property of their respective owners. The APC SurgeArrest Surge Protector + Battery Backup is shipped with the battery disconnected. The unit will not operate until the battery is connected. NOTE: Small sparks may occur during battery connection. This is normal. Surge Protection These outlets provide full-time protection from surges even if the unit is switched OFF. Plug your printer, fax machine, scanner, or other peripheral that does not need battery power into these outlets. Battery Backup + Surge Protection These outlets are powered whenever the unit is switched ON. During a power outage or other utility problems (brownouts, overvoltages), these outlets will be powered for a limited time by the internal battery. Plug your computer and 17” (or smaller) monitor, into these two outlets. Connect FAX/Modem/Phone The unit protects a single line (2-wire) fax, modem or phone from surges when it is connected as shown below. Connect AC Line Cord Connect the AC line cord to a 230-volt outlet. The Surge Protector + Battery Backup should be allowed to charge for at least 16 hours to ensure sufficient runtime. The unit is being charged whenever it is connected to utility power, and the unit is turned ON. Power ON the unit by pressing the ON/OFF button. Turn on your equipment. The Surge Protector + Battery Backup provides status indications through the flashing of the “Power On” indicator, as well as audible beeps. The indications are as follows: Status Visual Indications Audible Indication Alarm Terminates When On Line - Unit is supplying conditioned utility power to your equipment Power On LED - ON None n/a On Battery - Unit is supplying battery power to the equipment connected to the battery powered outlets Power On LED - ON (off during beep) Beeping 4 times every 30 seconds Unit returns to an On Line status or when the unit is turned off. Low Battery Warning - Unit is supplying battery power and the battery is nearly depleted. Once depleted, the unit will turn off. Power On LED - Flashing Rapid beeping (one second intervals) Unit is turned OFF, returns to On Line or when the battery is finally exhausted and the unit turns off. Replace Battery - Battery may need to be replaced, or the battery is not connected. Power On LED - Flashing Continuous tone. Unit is turned OFF and then ON and it passes a subsequent battery test. (This test occurs automatically whenever the unit is turned ON and every 14 days) Overload Shutdown - During On Battery operation a battery-power outlet was overloaded. Power On LED - OFF Continuous tone. Unit is turned off using the ON/OFF button. Status Indications Telephone Wall Fax/Modem/Phone + Battery Backup (BE325-UK) 32 - 104oF (0 - 40oC) Note: The on/off switch is illuminated when in the ON position. The switch may flash to indicate changing power conditions (see Status Indications). Circuit Breaker AC Line Cord 230-Volt Wall Outlet Outlet w w w.apc.com ® Battery Backup plus Surge Protection Surge Protection Side View Top View Push to Reset Circuit Breaker RJ-11 Connectors End View End View Top View Battery Backup plus Surge Protection 2 5 1 3 4 w w w.apc.com Surge Protector + Battery Backup 325VA w w w.apc.com Surge Protector + Battery Backup 325VA Consult APC Online Technical Support or call APC Technical Support for assistance with problems that cannot be resolved using the table below: Troubleshooting Problem Probable Cause Solution Unit will not turn on. Battery is disconnected. Circuit Breaker has tripped. Utility power not available at the wall outlet. Connect the battery (see Connect Battery). Reduce the amount of equipment plugged into the “Battery Backup + Surge Protection” outlets. Reset the Circuit Breaker by pushing it back in. Reduce the amount of equipment plugged into the “Surge Protection” outlets. Resetthe Circuit Breaker by pushing it back in. Ensure that the fuse or circuit breaker for the outlet is okay, and that the wall switch controlling the outlet (if any) is in the ON position. Connected equipment loses power. Equipment is connected to the “Surge Protection” outlets. The unit is overloaded. The unit has exhausted its available battery power. Connected equipment does not accept the step- approximated sine waveform the unit. The unit may require service. Ensure that the equipment you want to stay powered during a power failure is plugged into the “Battery Backup + Surge Protection” outlets and NOT the “Surge Protection” outlets. Make sure that the equipment plugged into the outlets of the unit are notoverloading the capacity of the unit. Try removing some of the equipment and see ifthe problem continues. The unit can only operate on battery power for a limited amount of time. The unitwill eventually turn off when the available battery power has been used. Allow the unit to recharge for 16 hours before continuing use of the unit. The output waveform is designed for...