When making connections, be sure to: • turn off all equipment before making any connections. • use the proper cables for each connection. • insert the plugs of the cables properly; plugs that are not fully inserted often generate noise. When pulling out a cable, be sure to pull it out from the plug, not the cable itself. AUDIO IN MOUSEINPUT A S VIDEO VIDEO L AUDIO R AUDIO OUT S-Video cable (not supplied) Audio/video cable (supplied) Active speakers to audio/video outputs1) to S video output1) VCR Right side 1) When both the S VIDEO and VIDEO jacks are connected to the external equipment, the input signal from the S VIDEO jack is selected. INPUT A S VIDEO VIDEO L AUDIO R AUDIO OUT AUDIO IN MOUSE Right side 15k RGB/Component equipment to RGB/ component output SMF-402 Signal Cable (not supplied) 3X phono jack yHD D-sub 15-pin (male) Stereo audio connecting cable (not supplied) to audio output Notes • Set the aspect ratio using ASPECT in the INPUT SETTING menu according to the input signal. • When you connect the unit to 15k RGB/component video equipment, select RGB or component with the INPUT-A setting in the SET SETTING menu. • Use the composite sync signal when you input the external sync signal from 15k RGB/component equipment. 16 (GB) Projecting Rear remote control detector ON/STANDBY indicator APA key APA key COMMAND MUTING I / 1INPUT APA MENU LASER ENTER RESET R CLICK PICTUREAUDIO ONOFF APA VOLUME INPUT MENU ENTERRESET ON /STANDBY POWER SAVING TEMP /FAN LAMP /COVER 5 4 1 2 32 3 1 After all equipment is connected completely, plug the AC power cord into the wall outlet. The ON/STANDBY indicator lights in red and the projector goes into the standby mode. 2 Press the I / 1key on the Remote Commander or on the control panel. The ON/STANDBY indicator lights in green. 3 Turn on equipment connected to the projector. Press the INPUT key on the Remote Commander or on the control panel to select the input source. Projecting INPUT-A: Selects audio and video signals input from the INPUT A connector. VIDEO: Selects audio and video signals input from the video/audio input connector. (If you connect to both the S VIDEO and VIDEO jacks, the signal from the S VIDEO jack is selected.) 4 Turn the zoom ring to adjust the size of the picture. 5 Turn the focus ring to adjust the focus. Note Looking into the lens when projecting may cause injury to your eyes. To Press Adjust the volume the VOLUME +/– keys on the control panel or on the Remoter Commander. Cut off the sound the AUDIO MUTING key on the Remote Commander. To restore the sound, press the AUDIO MUTING key again or press the VOLUME + key. Cut off the picture the PICTURE MUTING key on the Remote Commander. To restore the picture, press the PICTURE MUTING key again. To get the clearest picture You can get the suitable picture when a signal from the computer is input. Press the APA key on the Remote Commander or on the control panel. The picture is automatically adjusted to be projected clearest. Notes • Adjust the signal when the still picture is displayed on the screen. • If you switch the input signal or re-connect a computer, press the APA key again to get the suitable picture. • “ADJUSTING” appears on the screen. Press the APA key again during the adjustment to restore the original screen. • “Complete!” appears on the screen when the picture is adjusted properly. The picture may not be adjusted properly depending on the kinds of input signals. • Adjust DOT PHASE in the INPUT SETTING menu when you adjust the picture manually. For details on DOT PHASE, see page 21 (GB). 17 (GB) Projecting To turn off the power 1 Press the I / 1key on the Remote Commander or on the control panel. The following message appears to confirm if you want to turn off the power. POWER OF F ? Please press I /u key again. Note The message will disappear if you press any key except the I / 1key, or if you do not press any key for five seconds. 2 Press the I / 1key on the Remote Commander or on the control panel again. The ON/STANDBY indicator flashes in green and the fan continues to run for about 90 seconds to reduce the internal heat. Also, the ON/STANDBY indicator flashes quickly for the first 30 seconds. During this time, you will not be able to turn the power back on with the I / 1key. 3 Unplug the AC power cord from the wall outlet after the fan stops running and the ON/STANDBY indicator lights in red. When you cannot confirm the on-screen message When you cannot confirm the on-screen message in a certain condition, you can turn off the power by holding the I / 1key on the Remote Commander or on the control panel for about one second. Note Do not unplug the AC power cord while the fan is still running; otherwise, the fan will stop although the internal heat is still high, leading to breakdown of the projector. 18 (GB) Using the MENU / The PICTURE CTRL Menu Using the MENU The projector is equipped with an on-screen menu for making various adjustments and settings. To select the language used ...