Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Connections Preparations Unpacking Check the carton to make sure it contains the following items: Remote control (1), Size AA (R6) batteries (2) Signal interface cable (1) Air filter (for replacement) (1) Adjuster spacers (2) AC power cord (1) Operating Instructions (this manual) (1) Inserting the batteries into the remote control Insert the batteries E side first as shown in the illustration. Inserting them forcibly or with the polarities reversed may cause a short circuit and may generate heat. Unpacking 5GB Connections and Preparations GB 6 Step 1: Installing the Projector You can obtain good picture quality even when you project the picture from the side of the screen (“Side Shot”) (1 page 8). You can enjoy home entertainment with this projector in various situations. Enjoying home theater Enjoying video games on a large screen Watching sports, etc. with your company Do not place the projector in the following situations, which may cause malfunction or damage to the projector. Poorly ventilated Highly heated and humid Subject to direct cool or warm air from an air-conditioner Installing in such a location may cause malfunction of the unit due to moisture condensation or rise in temperature. Step 1: Installing the Projector Before Setting Up the Projector Near a heat or smoke sensor Placing the projector upside down Connections Preparations Malfunction of the sensor may be caused. Very dusty and extremely smoky Do not use the projector under the following conditions: Tilting the unit extremely Blocking the ventilation holes Do not place the projector upside down on the table etc. The projector will be unstable. Note Installing the unit at altitudes When using the projector at an altitude of 1,500 m or higher, turn on high altitude mode in the INSTALL SETTING menu. Failing to set this mode when using the projector at high altitudes could have adverse effects, such as reducing the reliability of certain components. Ventilation Ventilation holes holes (exhaust) (intake) Tip For further details on the location of the ventilation holes (intake or exhaust), see “Location of Controls” on pages 45 and 46. Placing the projector without the adjuster Step 1: Installing the Projector 7GB Connections and Preparations Connections and Preparations Installing the Projector and a Screen The installation distance between the projector and screen varies depending on the size of the screen. Note When installing the projector and screen, be sure not to tilt them. If you tilt either or both of them, the adjustment cannot be correctly carried out. 1 Determine the installation position of the projector and screen. a e b cd f8° 5° Screen Projector a: Minimum projection distance between the screen and the center of the projector’s lens when you place the projector on the side (“Side Shot”), or when you place the projector with the center of the screen and the center of the lens aligned. b: Maximum projection distance between the screen and the center of the projector’s lens when you place the projector on the side, or when you place the projector with the center of the screen and the center of the lens aligned. c: Maximum horizontal distance between the right/left end of the screen and the center of the projector’s lens when the projector is placed on the side (when you use projection distance a) d: Maximum horizontal distance between the right/left end of the screen and the center of the lens when the projector is placed on the side (when you use projection distance b) e: Maximum vertical distance from the bottom of the screen to the center of the projector’s lens when you place the projector on the side (when you use projection distance a) f: Maximum vertical distance from the bottom of the screen to the center of the projector’s lens when you place the projector on the side (when you use projection distance b) When projecting using “Side Shot” adjustment only (1 page 17) Position the projector with the lens end within the area in the illustration, by using the values a, b, c and d in the table below as a guide. Unit: m (feet) Screen size (inches) 40 60 80 100 120 150 a 1.1 (3.6) 1.7 (5.6) 2.2 (7.2) 2.8 (9.2) 3.3 (10.8) 4.2 (13.8) b 1.2 (3.9) 1.8 (5.9) 2.4 (7.9) 3 (9.8) 3.6 (11.8) 4.5 (14.8) c -0.2 (-0.7) -0.2 (-0.7) -0.3 (-1) -0.4 (-1.3) -0.4 (-1.3) -0.4 (-1.3) d 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) Tip The table shows the distances when projecting the video signals. Distances used for projecting a 1080i/720p format signal and computer’s signal are shown on page 40 . Note If you project the picture using “Side Shot” only, set “V Keystone” in the INSTALL SETTING menu to “Manual,” and adjust the level to “0.” When projecting using both “Side Shot” and “V Keystone” adjustments (1 page 18) Position the projector with the lens end within the area in the illustration, by using the values a to f in the table below as a guide. Unit: m (feet) Screen size (inches) 40 60 80 100 120 150 a 1.2 (3.9) 1.7 (5.6) 2.2 (7.2) 2.8 (9.2) 3.4 (11.2) ...