Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
qj qjqjqjqjConnector panel For details, see “Connector Panel” on page 12. qk qkqkqkqkSecurity lock Connects to an optional security cable (Kensington’s). The security lock corresponds to Kensington’s MicroSaver Security System. If you have any comment, contact: Kensington 2853 Campus Drive San Mates, CA 94403 U.S.A. Tel: 800-535-4242: extension 3348 Home page address: ql qlqlqlqlVentilation holes (intake) How to use the adjuster To adjust the height Adjust the height of the projector as follows: 1 Lift the projector and press the RELEASE button. The adjuster will extend from the projector. RELEASE button 2 While pressing the button, lower the projector. Then, release the button. The adjuster can be set at 6 positions. Notes • Be careful not to let the projector down on your fingers. • Do not push hard on the top of the projector with the adjuster out. GB 10 Location and Function of Controls 5 Indicators Control Panel • LAMP/COVER: Lights up or flashes under the following conditions: – Lights up when the lamp has reached the end of its life or RESET MENU POWER INPUT APA VOLUME POWER SAVING ON/STANDBYFAN/TEMPLAMP/COVER ENTER +– 1 I / 1 1111 (on/standby) key Turns on and off the projector when the becomes a high temperature. – Flashes when the lamp cover or air filter cover is not secured firmly. • FAN/TEMP (Temperature): Lights up or flashes under the following conditions: – Lights up when temperature inside the projector becomes unusually high. – Flashes when the fan is broken. • POWER SAVING: Lights up when the projector is in power saving mode. Overview When POWER SAVING in the SET SETTING menu is set to ON, the projector is in standby mode. The ON/ STANDBY indicator lights in green when the power is turned on. When turning off the power, press the I / 1 key twice following the message on the screen, or press and hold the key for about one second. For details on steps for turning off the power, see “To turn off the power” on page 24. 2 INPUT key Selects the input signal. Each time you press the key, the input signal switches as follows: INPUT A t VIDEO t S VIDEO projector goes into power saving mode if no signal is input for 10 minutes. Although the lamp goes out, the cooling fan keeps running. In power saving mode, any key does not function for the first 30 seconds. The power saving mode is canceled when a signal is input or any key is pressed. • ON/STANDBY: Lights up or flashes under the following conditions: – Lights in red when a AC power cord is plugged into a wall outlet. Once in standby mode, you can turn on the projector with the I / 1 key. – Lights in green when the power is turned on. – Flashes in green while the cooling t 3 APA (Auto Pixel Alignment) key fan runs after the power is turned off with the I / 1 key. The fan runs for about 90 seconds after the power is turned off. Adjusts a picture clearest automatically while a signal is input from a computer. 4 VOLUME +/– keys Adjust the volume of the built-in speakers. + : Increases the volume. – : Decreases the volume. The ON/STANDBY indicator flashes quickly for the first 30 seconds. During this time, you cannot light up the ON/STANDBY indicator with the I / 1 key. For details on the LAMP/COVER and the FAN/TEMP indicators, see on page 35. 11 11 GB Location and Function of Controls 6 ENTER key Enters the settings of items in the menu system. 7 Arrow keys (M MMMM/m mmmm/< <<<Эта инструкция также подходит к моделям:
Проекторы - VPL-CX1 (1.38 mb)