|
Фрагмент инструкции
On air filter To maintain optimal performance, clean the air filter every 300 hours. GB 24 Projecting Effective Tools for Your Presentation To enlarge the image (Digital Zoom function) You can select a point in the image to enlarge. 1 Project the original size picture and press the D ZOOM + key on the Remote Commander. One of images divided into 16 is highlighted at the center of the image. 2 Move the highlight portion to the point you want to enlarge by pressing the arrow keys (M/m/,). 3 Press the D ZOOM + key again. The highlight portion displayed in step 2 is enlarged. By pressing the + key repeatedly, the image size increases. (ratio of enlargement: max. 4 times) Use the arrow keys (M/m/,) to scroll the enlarged image. To return the image back to its original size Press the D ZOOM – key on the Remote Commander. Just pressing the RESET (ZOOM) key returns the image back to its original size immediately. Setting Up and Projecting 25 25 GB Projecting B Adjustments and Settings Using the Menu Using the MENU The projector is equipped with an on-screen menu for making various adjustments and settings. You can change the menu language displayed in the on-screen menu. To change the menu language, see “Selecting the Menu Language” on page 20. 1 Press the MENU key. The menu appears. The menu presently selected is shown as a yellow button. 80 50 PICTURE CTRL CONTRAST: BRIGHT: GAMMA MODE: GRAPHICS COLOR TEMP: HIGH INPUT-A 2 Use the M or m key to select a menu, then press the , or ENTER key. The selected menu appears. Menus Setting items SET SETTING STATUS: ON INPUT-A: RGB KEYSTONE MEMORY: ON DIGITAL KEYSTONE: OFF LANGUAGE: ENGLISH INSTALLATION: FLR-FRONT POWER SAVING: OFF SIRCS RECEIVER: FRONT&REAR LAMP TIMER: 00010h INPUT-A 3 Select an item. Use the M or m key to select the item, then press the , or ENTER key. 4 Make the setting or adjustment on an item. • When changing the adjustment level: To increase the number, press the Mor , key. To decrease the number, press the m or < key. Press the ENTER key to restore the original screen. • When changing the setting: Press the M or m key to change the setting. Press the ENTER or < key to restore the original screen. To clear the menu Press the MENU key. The menu disappears automatically if a key is not pressed for one minute. To reset items that have been adjusted Press the RESET key. “Complete!” appears on the screen and the settings appearing on the screen are reset to their factory preset values. Items that can be reset are: •“CONTRAST,”“BRIGHT,”“COLOR,” “HUE,” and “SHARP” in the PICTURE CTRL menu •“DOT PHASE,”“SIZE,”and “SHIFT”in the INPUT SETTING menu •“DIGITAL KEYSTONE” in the SET SETTING menu About the memory of the settings The settings are automatically stored in the projector memory. If no signal is input If there is no input signal, “NO INPUT– Cannot adjust this item.” appears on the screen. GB 26 Using the MENU The PICTURE CTRL Menu The PICTURE CTRL (control) menu is used for adjusting the picture. Items that cannot be adjusted depending on the input signal are not displayed in the menu. For details on the unadjustable items, see page 42. When the video signal is input When the RGB signal is input PICTURE CTRL CONTRAST: BRIGHT: COLOR: HUE: SHARP: D. PICTURE: COLOR TEMP: COLOR SYS: VIDEO 80 50 50 50 50 OFF LOW AUTO 80 50 PICTURE CTRL CONTRAST: BRIGHT: GAMMA MODE: GRAPHICS COLOR TEMP: HIGH INPUT-A Menu Items CONTRAST Adjusts the picture contrast. The higher the setting, the greater the contrast. The lower the setting, the lower the contrast. BRIGHT Adjusts the picture brightness. The higher the setting, the brighter the picture. The lower the setting, the darker the picture. COLOR Adjusts color intensity. The higher the setting, the greater the intensity. The lower the setting, the lower the intensity. HUE Adjusts color tones. The higher the setting, the picture becomes greenish. The lower the setting, the picture becomes purplish. SHARP Adjusts the picture sharpness. The higher the setting, the sharper the picture. The lower the setting, the softer the picture. D. (Dynamic) PICTURE Emphasizes the black color. ON: Emphasizes the black color to produce a bolder “dynamic” picture. OFF: Reproduces the dark portions of the picture accurately, in accordance with the source signal. GAMMA MODE Selects a gamma correction curve. GRAPHICS: Improves the reproduction of halftones. Photos can be reproduced in natural tones. TEXT: Contrasts black and white. Suitable for images that contain lots of text. COLOR TEMP Adjusts the color temperature. HIGH: Makes the white color bluish. LOW: Makes the white color reddish. COLOR SYS (System) Selects the color system of the input signal. • AUTO: NTSC3.58, PAL, SECAM and NTSC4.43 (switched automatically) • PAL-M/N: PAL-M/PAL-N and NTSC3.58 (switched automatically) Normally, set to AUTO. If the picture is distorted or colorless, select the color system according to the input signal. Adjustments and Settings Using the Menu 27 27 GB T...
Эта инструкция также подходит к моделям:Проекторы - VPL-CX10 (1.57 mb)