Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
RS-232C CONTROL RGB AUDIO MONITOR OUTPUT RGB S-VIDEO VIDEO VIDEO INPUT L - AUDIO -R AUDIO RGB INPUT 1 2 3 4 Anti-theft lock Rear side 1 2 3 4 Speaker Infrared remote sensor Intake holes CONTROL connector 4014 To connect a computer to control the projector. MONITOR OUTPUT connectors (RGB output, AUDIO output) 14 To connect to a monitor or audio equipment. RGB INPUT connectors (RGB input, AUDIO input) 15 To connect a computer or video equipment with component video outputs, etc. VIDEO INPUT connectors (S-VIDEO input, VIDEO input, AUDIO input) 14 To connect a video equipment, etc. (Continued) 14 13 11 12 1 6 VIDEORGB AUTO SET KEYSTONE RESIZE FREEZE MENU RESET +- ENTER MUTE MARKER CALL ON/ STANDBY 2 10 8 3 7 5 1 2 3 4 5 6 7 8 14 13 12 11 10 9 Before use (Continued) Installing batteries 1) Open the cover. 2) Install the batteries. Make sure that the +/– polarities match the illustration in the compartment. 3) Attach the cover. Notes Using batteries incorrectly can cause them to leak or burst. Strictly observe the following. • Install the batteries with their + and – ends facing correctly. • Do not charge, heat, disassemble, or short the batteries or throw them into a fire. • Do not leave exhausted batteries in the remote control. • Do not mix different types of batteries or new and old batteries. • When you will not be using the remote control for a prolonged period, take the batteries out of the remote control. • When the remote control stops working or only works from very close distance, replace all the batteries with new ones. • When replacing the batteries, use a more longer life alkaline batteries. • If a battery leaks, carefully wipe off any residue inside the battery case before loading new batteries. Remote control operation Point the remote control at the infrared remote sensor and press a button. Front side Rear side 15° 15° 15° 15° Distance : within about 5 meters from the front of the remote sensor. Angle : within about 15° of the remote sensor in every direction. (Continued) Before use (Continued) Notes Power supply cord selection • The remote control may not operate when there is sunlight or other strong light such as a fluorescent lamp shining on the remote sensor. • Operate the remote control from a position where the remote sensor is visible. • Do not drop the remote control or otherwise jolt it. • Keep the remote control out of locations with excessively high temperature or humidity. • Do not get water on the remote control or place wet objects on it. • Do not disassemble the remote control. • Under unusual circumstances the remote control may not operate well due to the location being used or the surroundings. At such times, change the direction of the remote control to the projector and retry the operation. If your line voltage is 220 to 240, use one of the following types of cable. In Singapore, use the UK type plug cable. (The UK type plug [MP5004] of this model is approved by PSB.) Plug configuration Plug type Line voltage EURO 220 – 240V UK 220 – 240V Use a 5A fuse which is approved by ASTA or BSI to BSI362. Always replace the fuse cover after changing the fuse. Connections and installation 14 Connections (Continued) Connecting video equipment Check that the power for the projector and computer is off before connecting the cables. Output terminals Check that the power for the projector and computer is off before connecting the cables. Notes • Sound of the source which you select is output to the connected stereo system, etc. • The MONITOR OUTPUT (RGB output) connector always sends out a signal which is input to the RGB INPUT (RGB input) connector regardless of your source selection. • Even while the projector is in standby mode, the MONITOR OUTPUT (RGB output) connector continues its output. Note Several video equipments can be connected to the S-VIDEO jack and VIDEO jack separately. RS-232C CONTROL RGB AUDIO MONITOR OUTPUT RGB S-VIDEO VIDEO VIDEO INPUT L - AUDIO -R AUDIO RGB INPUT To VIDEO INPUT (S-VIDEO) To S-VIDEO output To Video output (yellow) To Audio output (white) To Audio output (red) yellow white red Adapter for SCART socket (supplied) Audio/Video cable (supplied) S-VIDEO cable (not supplied) To RGB INPUT (RGB) To RGB INPUT (AUDIO) To PR(CR) output To PB(CB) output To Y output Audio cable (not supplied) (not supplied) To audio output L (white) To audio output R (red) To VIDEO INPUT (VIDEO) (yellow) To VIDEO INPUT (AUDIO L) (white) To VIDEO INPUT (AUDIO R) (red) To SCART socket Connecting to SCART socket Video tape player Video player with component video outputs RS-232C CONTROL RGB AUDIO MONITOR OUTPUT RGB S-VIDEO VIDEO VIDEO INPUT L - AUDIO -R AUDIO RGB INPUT To MONITOR OUTPUT (AUDIO) o3.5mm STEREO mini plug (Audio output level is constant.) To audio input Audio cable (not supplied) Connect a stereo system for dynamic sound. You can connect an extra monitor to view the picture. You can connect a computer to control the projector. 40 Connections and installation (Continued) Con...
Эта инструкция также подходит к моделям:Проекторы - TLPMT3U (598.98 kb)