No adjustments are necessary. 2-9 Installation and Connection 2-10 Connecting the Power Installation and Connection 2-10 2-11 Connecting with a PC 1. Connect the [PC IN] port on the rear side of the projector to the PC video out (D-sub) port of the PC using a PC video cable. 2. Plug in the power cords of the projector and the PC. 3. Connect the [PC/DVI AUDIO IN] input port of the projector to the speaker output ports of the PC using an audio cable. 0 This product supports Plug and Play. If you use Windows XP, you do not need to set up the driver on your PC. Using the Projector 1. Turn on the projector, and then press the [SOURCE] button to select . If the Mode is not available, make sure the PC video cable is properly connected. 2. Turn on the PC, and then set the PC Environment (screen resolution, etc.) if necessary. 3. Adjust the screen. (). 2-11 Installation and Connection 2-12 Connecting a PC using an HDMI/DVI cable —_—_—_—_— Make sure that your PC and projector are turned off. 1. Connect the [HDMI/DVI IN] terminal of the projector to the HDMI or DVI terminal of your PC using a HDMI/HDMI or HDMI/DVI cable (Not supplied). 0 For the input signals supported, see "PC Timing (D-Sub/HDMI)" in section 2-9, "Supported Display Modes." 2. If you connected using a HDMI/DVI cable, connect the [PC/DVI AUDIO IN] terminal of the projector to the Audio out terminal of your PC using an audio cable (Not supplied). - If you connected with a HDMI/HDMI cable, you do not need an audio cable. Installation and Connection 2-12 2-13 Connecting an External Monitor You can view an image on both your projector and a separate monitor at the same time. Make sure that your PC and projector are turned off. 1. Connect the [PC IN] terminal at the back of the projector to the D-Sub (PC, VGA) terminal of your PC using a D-Sub cable. 2. Connect the [PC OUT] terminal of the projector to the D-Sub terminal of a monitor using a D-Sub cable. - When connecting a monitor using the [PC OUT] function, make sure to connect your PC to the [PC IN] terminal. - The video on the monitor connected to the [PC OUT] terminal will be normal even if you see a blank screen on your projector. - The [PC OUT] function will not operate in standby mode. 2-13 Installation and Connection 2-14 Connecting an HDMI-Compatible Device Make sure that the AV device and your projector are turned off. 1. Connect the [HDMI/DVI IN] terminal at the back of the projector to the HDMI or HDMI/DVI output terminal of the digital output device using an HDMI/DVI or HDMI/HDMI cable. - If you are connecting to the HDMI output terminal on the digital output device, use an HDMI/HDMI cable. - For supported input signal formats, resolutions, and frequencies, see AV Timing(HDMI) in Section 2-9, “Supported Display Modes”. 2. If you connected using a HDMI/DVI cable, connect the [PC/DVI AUDIO IN] terminal on the projector to the Audio out terminal on your digital output device using an audio cable (Not supplied). - If you connected with a HDMI/HDMI cable, you do not need an audio cable. Installation and Connection 2-14 2-15 Connecting an AV device using a D-Sub cable Make sure that the AV device and your projector are turned off. 1. Connect the [PC IN] terminal at the back of the projector to the D-Sub terminal of your AV device using a D-Sub cable. - For supported input signal formats, resolutions, and frequencies, see AV Timing (D-Sub) in Section 2-9, “Supported Display Modes”. 2. Connect the [PC/DVI AUDIO IN] terminal at the back of the projector to the Audio out terminal of your AV device using an audio cable (Not supplied). 2-15 Installation and Connection 2-16 Connecting an AV device with component output Make sure that the AV device and your projector are turned off. 1. Connect the [PC IN] terminal on the back of the projector to the Component terminal on your AV device using a D-Sub to Component cable (Not supplied). This cable has a D-Sub connector on one end and three RCA jacks on the other. - For supported input signal formats, resolutions, and frequencies, see AV Timing (D-Sub) in Section 2-9, “Supported Display Modes”. 2. Connect the [PC/DVI AUDIO IN] terminal on the back of the projector and the Audio out terminal on your AV device using an audio cable (Not supplied). Installation and Connection 2-16 2-17 Connecting using a Video/S-Video cable Make sure that the AV device and your projector are turned off. 1. Connect the [VIDEO] or [S-VIDEO] terminal and the AV device using a Video cable (Not supplied) or S-Video cable (Not supplied). - For supported input signal formats, see AV Timing (VIDEO/S-VIDEO) in Section 2-9, "Supported Display Modes”. 2. Connect the [AV IN R-AUDIO-L] terminal on the back of the projector and the Audio out terminal on your AV device using an audio cable (Not supplied). 2-17 Installation and Connection 2-18 Connecting an External Speaker You can hear sound through an ...
)
