Оценок - 3, средний балл: 4.3
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
SP-L200 : Provides a bright screen of 2000 lumen. - Compact size, lightweight, and good portability Minimized fan noise -Minimizes the noise generated by the product’s fan by optimizing the internal air flow and the fan installation structure. Various input terminals -Increases the connectivity to peripheral devices by providing various terminals, such as 2 D-Sub 15p (supporting DTV signal), S-Video, and Video terminals. Audio Output -There are two stereo speakers on the right and left and a 5-band equalizer is supported. User adjustments - This unit allows adjustment of each input port. - The unit has a reference pattern that can be used for positioning and adjustment. | Product Features | Product Views | Remote Control | Product Specifications | Front/Upper Side 1. Indicators - STAND BY (Blue LED) - LAMP (Blue LED) - TEMP (Red LED) . Refer to the LED Indications. 2. VOL - / + & Select and Move Button Adjusts the volume. Use this button to move to or select an item within a menu. 3. MENU Button Use this button to enter or exit a menu or to move forward in a menu. 4. SOURCE Button Used to select input signals from the external sources. Unpacking 5. POWER( ) Button Used to turn the projector on or off. 6. Lens 7. Remote Control Signal Receiver 8. Focus Ring Used for Focus Adjustment. 9. Zoom Knob Used to enlarge or reduce image size. 10.Lens cover Warranty Card/ Registration Card Quick Installation Guide / Safety Guide User Manual CD (Not available in all locations) Remote Control/ 1 Batteries (CR2025) Power Cable Cleaning Cloth (Not available in all locations) D-Sub Cable LED Indications :Light is On :Light is Blinking :Light is Off STAND BY LAMP TEMP Information If you press the POWER button on the remote control or projector, the screen appears within 30 seconds. The projector is in normal operating condition. This state appears when the projector is preparing an operation after the POWER button on the projector or the remote control has been pressed. The POWER button is pressed to turn off the projector, and the cooling system is in operation to cool off the inside of the projector. (Operates for about 30 seconds.) Refer to Action 1 below if the cooling fan inside the projector is not in normal operation condition. Refer to Action 2 below if the lamp cover protecting the lamp unit is not closed properly. This indicates that the lens cover does not open completely. Refer to Action 3 below. This indicates that it has changed to Cooling mode, because the internal temperature of the projector has increased beyond the maintenance limit. Refer to Action 4 below. This indicates that the power is turned off automatically because the internal temperature of the projector has increased beyond the maintenance limit. Refer to Action 5 below A problem has occurred with the operation of the lamp. Refer to Action 6. Clearing Indicator Problems Measures If the symptom remains even after disconnecting and then reconnecting the power cord and turning the projector on again, contact your product provider or our service center. Check if the screws on the side of the projector are correctly locked, and if they are locked normally, contact your product distributor or a service center. Open the lens cover completely. If the lens cover is not open completely while operating the projector, both the video and audio are turned off automatically. If this status persists for ten minutes, the projector is turned off automatically. If the internal temperature of the projector has increased beyond the maintenance limit, it is changed to Cooling mode before it is turned off automatically. Classification Action 1 Action 2 Action 3 State When the cooling fan system is not in normal operating condition. When the lamp cover protecting the lamp unit is not properly closed or the sensor system is not in normal operating condition. The status that the lens cover is not open completely. This indicates that it has changed * Cooling mode: The fan speed has increased and the projector lamp has been changed to ECO mode. Check whether the ventilating hole of the projector is blocked. Check the air filter and clean if blocked. Check whether the surrounding temperature of the projector is higher than the standard temperature range of the projector. Cool the projector sufficiently and operate it again. Check whether the ventilating hole of the projector is blocked. Check the air filter and clean if blocked. Check whether the surrounding temperature of the projector is higher than the standard temperature range of the projector. Cool the projector sufficiently and operate it again. If the same problem occurs continually, contact your product distributor or service center. Turn the power off, wait for a sufficient amount of cooling time and then turn the power on to operate. If the same problem occurs continually, contact your product distributor or service center. to Cooling mode, because the internal temperature of the projector has increased beyond Ac...
Эта инструкция также подходит к моделям:Проекторы - L250 (1.25 mb)
Проекторы - SP-L220 (1.25 mb)
Проекторы - SP-L220W (1.25 mb)
Проекторы - SP-L250 (1.25 mb)