Оценок - 5, средний балл: 4
(
)
)
|
Фрагмент инструкции
(page 21) Zoom ring Air intake port Intake fresh air to control the temperature inside. Projection lens Adjust the position of the projected image. Shift lever Lens cover Protects the Projection lens Remote control from dust or dirt. signal receptor Receive a signal from the Remote control. (page 22) Illuminates or flashes to indicate the status of the lamp unit. (page 36) 2.0 power zoom lens. Control panel About Your Projector ENGLISH - 13 Preparation .. Back and bottom view NOTE: .. Do not cover the ventilation openings or place anything within 10 cm (4") of the vents as this may cause damage or injury. ..This projector should only be used with the attached Power cord to ensure optimum performance and avoid damage to the projector. Connect an RS-232C compatible cable for controlling the projector remotely via your PC. SERIAL Connect an RGB signal cable from your PC. PC IN Connect a YPBPR signal cable. COMPONENT IN Connect a S-VIDEO signal cable. S-VIDEO IN Connect an HDMI signal cable. HDMI IN Security lock Attach the commercial shackle lock, manufactured by Kensington, to protect your projector. Compatible with the Kesington MicroSaver Security System. Lamp unit component Houses the replaceable lamp unit. Contact the projector dealer or an authorized service center for replacement. (page 37) Front leg adjuster (L/R) Screw up/down to adjust the projection angle. (page 15) VIDEO IN Connect an RCA composite video cable. AC IN Connect the Power cord to supply electronic power to the projector. (page 26) MAIN POWER Switch the projector on/off. (page 19) Connecting terminals Air intake port Intake fresh air to control the temperature inside. 14 - ENGLISH Getting Started Setting up You can adjust the projection size with 2.0 power zoom lens. Calculate and define the throw distance as follows. * All measurements above are approximate and may differ slightly from the actual measurements. .. Calculation methods for screen dimensions You can calculate more detailed screen dimensions from the screen diagonal. * The results above are approximate and may differ slightly from the actual measurements. Screen size and throw distance Projection size (16 : 9) Throw distance (L) Diagonal length (SD) Screen height (SH) Screen width (SW) Minimum distance (LW) Maximum distance (LT) 1.01 m (40") 0.50 m (1'7") 0.89 m (2'11") 1.2 m (3'11") 2.4 m (7'10") 1.27 m (50") 0.62 m (2') 1.11 m (3'7") 1.5 m (4'11") 3.0 m (9'10") 1.52 m (60") 0.75 m (2'5") 1.33 m (4'4") 1.8 m (5'10") 3.7 m (12'1") 1.77 m (70") 0.87 m (2'10") 1.55 m (5'1") 2.1 m (6'10") 4.3 m (14'1") 2.03 m (80") 1.00 m (3'3") 1.77 m (5'9") 2.4 m (7'10") 4.9 m (16') 2.28 m (90") 1.12 m (3'8") 1.99 m (6'6") 2.7 m (8'10") 5.5 m (18') 2.54 m (100") 1.24 m (4') 2.21 m (7'3") 3.1 m (10'2") 6.2 m (20'4") 3.05 m (120") 1.49 m (4'10") 2.66 m (8'8") 3.7 m (12'1") 7.4 m (24'3") 3.81 m (150") 1.87 m (6'1") 3.32 m (10'10") 4.6 m (15'1") 9.3 m (30'6") 5.08 m (200") 2.49 m (8'2") 4.43 m (14'6") 6.2 m (20'4") 12.4 m (40'8") NOTE: .. Do not use the projector at a raised or a horizontally tilted position as it may cause malfunction of the projector. .. Make sure the projector lens surface is parallel with the screen. You can tilt the projector body approximately ± 30 degrees vertically. Overtilting may result in shortening the component’s life. ..For the best quality of the projection image, install a screen where sun light or room light does not shine directly onto the screen. Close window shades or curtains to block the lights. Screen SW = SD x 0.872 LW = 1.2244 x SD - 0.056 SH = SD x 0.490 LT = 2.4449 x SD - 0.056 Unit: m Setting up ENGLISH - 15 Getting Started You can use the projector with any of the following 4 projection methods. To set the desired method in the projector, see “INSTALLATION” on page 35. You can adjust the throwing angle by screwing the front legs up/down. This adjust the angle of the projector. Projection method .. Setting on a desk/floor and projecting from front .. Setting on a desk/floor and projecting from rear INSTALLATION: FRONT/DESK INSTALLATION: REAR/DESK .. Mounting in the ceiling and projecting from front .. Mounting in the ceiling and projecting from rear INSTALLATION: FRONT/CEILING INSTALLATION: REAR/CEILING NOTE: .. A translucent screen is required for REAR projection. .. When mounting the projector in the ceiling, the optional ceiling mount bracket (ET-PKX100) is required. Front leg adjuster and throwing angle NOTE: ..Heated air comes out of the Air exhaust port. Do not touch the Air exhaust port directly. .. If keystone distortion occurs, see “KEYSTONE” on page 33. Setting up 16 - ENGLISH Getting Started If the projector is not positioned right in front of the center of the screen, you can adjust the projected image position by moving the Shift lever within the shift range of the lens. .. Adjusting the Shift lever 1. Screw the Shift lever counterclockwise to unlock. 2. Move the Shift lever to adjust the projected image position 3. Screw the Shift lever ...