Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
To change the settings, refer to the AUDIO item in the SETUP menu. Y R L AUDIO IN2 AUDIO OUT CONTROL RGB IN1 RGB IN2 USB RGB OUT AUDIO IN1 VIDEO S-VIDEO CB/PB CR/PR K Y R L AUDIO IN2 AUDIO OUT CONTROL RGB IN1 RGB IN2 USB RGB OUT AUDIO IN1 VIDEO S-VIDEO CB/PB CR/PR K Y R L AUDIO IN2 AUDIO OUT CONTROL RGB IN1 RGB IN2 USB RGB OUT AUDIO IN1 VIDEO S-VIDEO CB/PB CR/PR K RGB IN2 RGB OUT RGB in Stereo mini audio cable Connecting to a monitor (output) Connecting to a speaker with amplifier (output) Use the RGB IN OUT switch to select RGB OUT (RGB OUT is selected if the switch is pushed in). RGB cable Audio in Putting batteries into the remote control / Connecting the power supply Putting batteries into the remote control WARNING >Always handle the batteries with care and use them only as directed. Improper use may result in battery explosion, cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment. • Be sure to use only the batteries specified. Do not use batteries of different types at the same time. Do not mix a new battery with used one. • Make sure the plus and minus terminals are correctly aligned when loading a battery. • Keep a battery away from children and pets. • Do not recharge, short circuit, solder or disassemble a battery. • Do not allow a battery in a fire or water. Keep batteries in a dark, cool and dry place. • If you observe a leakage of a battery, wipe out the flower and then replace a battery. If the liquid adheres to your body or clothes, rinse well with water immediately. 1. Remove the battery cover. Slide back and remove the battery cover in the direction of the arrow. 2. Insert the batteries. Align and insert the two AA batteries according to their plus and minus terminals as indicated in the remote control. 3. Close the battery cover. Replace the battery cover in the direction of the arrow and snap it back into place. Connecting the power supply WARNING >Please use extra caution when connecting the power cord, as incorrect or faulty connections may result in fire and/or electrical shock. • Only use the power cord that came with the projector. If it is damaged, contact your dealer to newly get correct one. • Only plug the power cord into an outlet rated for use with the power cord's specified voltage range. • Never modify the power cord. Never attempt to defeat the ground connection of the three-pronged plug. 1. Connect the connector of the power cord to the AC inlet of the projector. 2. Firmly plug the power cord's plug into the outlet. AC inlet Connector of the power cord 6 Zoom knobFocus ring 1. To select an input signal, use the button of INPUT (projector), or the buttons This product is able to turn off the main power during the cooling. However, please (1) Please do not turn the projector on again for at least 1 minute in this case. (2) During use or immediately after use, do not touch around the lamp and vents The message "Power off?" will appear on the screen for approximately 5 seconds. 2. Press the STANDBY/ON (projector or remote control) button again while the POWER (Blinking in orange) POWER POWER POWER (Blinking in green) (Steady green) (Steady orange) 1. To select an input signal, use the button of INPUT (projector), or the buttons This product is able to turn off the main power during the cooling. However, please (1) Please do not turn the projector on again for at least 1 minute in this case. (2) During use or immediately after use, do not touch around the lamp and vents The message "Power off?" will appear on the screen for approximately 5 seconds. 2. Press the STANDBY/ON (projector or remote control) button again while the POWER (Blinking in orange) POWER POWER POWER (Blinking in green) (Steady green) (Steady orange) Operating Operating WARNING >When the power is on, a strong light is emitted. Do not look into the lens of projector. Also do not peep at the inside of projector through a hole. Turning on the power POWER 1. Set the power switch to the ON position. 2. Press the STANDBY/ON (projector or remote control) button. Displaying of RGB, VIDEO or SEARCH (remote control). 2. To change the aspect ratio, use the button ASPECT (remote control). 3. To adjust the zoom and focus, use the zoom knob and the focus ring. Turning off the power pay special attention to below two points when you do: Neglect could shorten the lifetime of the lamp. of the projector. It could cause a burn. 1. Press the STANDBY/ON (projector or remote control) button. message appears. The projector lamp will go off, and the POWER indicator will begin blinking in orange. Then the POWER indicator will stop blinking and light in steady orange when the lamp cooling is complete. (Steady orange) 3. Make sure that the power indicator lights in steady orange, and set the power switch to the OFF position. The POWER indicator will go off. ENGLISH 7 Control buttons / Remote control Control buttons LAMP indicator TEMP indicator POWER indicator Cursor buttons ^,Ў,<,> STAN...
Эта инструкция также подходит к моделям:Проекторы - CP-S245 (1.71 mb)
Проекторы - CP-S240 (1.71 mb)
Проекторы - CP-X255 (1.71 mb)