Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
ON CD-ROM DISKS OR INTERNET-SITES) OR USED IN THEIR ENTIRE FORM OR IN EXCERPTS WITHOUT OUR PREVIOUS WRITTEN AGREEMENT. IF YOU ARE DOWNLOADING PDF-FILES FROM OUR INTERNET HOME-PAGE FOR YOUR PERSONAL USE, MAKE SURE TO CHECK FOR UPDATED VERSIONS. WE CANNOT TAKE ANY LIABILITY WHATSOEVER FOR DOWNLOADED FILES, AS TECHNICAL DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE. adjusting lever video setting knob optics‘ cover focus knob sliding switch lamp cover display IR-Receiver “Mode“ key Master Control “Reset“ key Knob “Lamp“ key “Film“ key 1.Contents 1. Contents 3 6. Functions 21 6.1 Wall Projection ................................. 21 2. Safety 5 6.2 Highspeed Shuttle/Rewinding ............. 25 6.3 Sprocket Projection ............................ 26 6.4 Loop Forming Position A/B ................. 27 3. General Product Information 7 6.5 Video...............................................29 6.6 ”Mode” Key (Unit Configuration) ........ 33 6.7 Controls ........................................... 36 4. Unpacking and Installation 9 6.8 Infrared Remote Control ..................... 41 6.9 Interfaces ......................................... 43 5. Initial Operation 11 7. Service and Maintenance 45 5.1 Precautions for Shipping .................... 11 7.1 Cleaning the Film Track ...................... 45 5.2 Video-Option .................................... 12 7.2 Cleaning Mirror and Lens ................... 47 5.3 Format masks .................................... 13 7.3 Shipping and Storage ........................ 48 5.4 IR-Remote Control .............................. 15 7.4 Replacing the Fuses ........................... 48 5.5 Switching on the LOCPRO 35 ............. 16 5.6 Switching on the HTI lamp .................. 17 8. Technical Data 51 5.7 Film loading ..................................... 18 5.8 Video...............................................19 Serial Interface (X1)....................................53 Contents Contents 9. Trouble-Shooting Table 55 10. ARRI Service 68 11. Index 69 Annex Interfaces 79 Service Instructions 80 2.Safety The functions and workmanship quality of this unit were tested at the factory. It complies strictly to the following European Guidelines: • Guideline 89/336 EEC of 3. May 1989 ”Guideline of the Council of 3. May 1989 for bringing into line the statutory regulations of the member countries about electromagnetic side-effects.” • Guideline 73/23 EEC of 19.02.73 ”Guideline of the Council of 19. Feb. 1973 for bringing into line the statutory regulations of the member countries with respect to electrical operating material for use within particular voltage limitations. The electric installation of the room in which the LOCPRO 35 is being used must comply with the demands of the IEC commitments. Warnings For your own safety, please adhere to the following warnings: Caution! – stands for danger of injury. Attention!– equipment damage possible. Note: Operational error possible! General Safety Specifications Caution: Danger of Injury! Never reach into the film channel while the LOCPRO 35 is running or remove the covers!! • In order to ensure safe and proper operation it is essential that you acquaint yourself with this user manual. • Assembly and initial operation are to be carried out only by persons familiar with the equipment. Safety Safety • Make sure the LOCPRO 35 stands securely and do not Important Notes block the air vents of the HTI lamp cooling fan on the bottom side! See e photo page 9. • Keep all inflammable material away from the air vents of the HTI lamp cooling fan. see e photo page 9. • For sufficient air cooling, it is essential that the air supply and escape vents on the sides are not blocked. see e photo page 9. • Disconnect the unit from the mains before starting maintenance or service! • The unit is to be opened only by a qualified electrical specialist. If fuses need to be replaced, ensure that only the values indicated are used. See chapter 7.4. • Repairs should be made by authorized service technicians only! • Use only original replacement parts and accessories! • Follow the maintenance instructions in this user manual. • Follow the shipping and storing instructions. • In humid weather please take the usual and customary safety measures. • In case of poor picture steadiness check the film guide for possible contamination, such as e.g. splicing residues or emulsion deposits.Clean if necessary! (see chapter 7.1) • Optical surfaces should only be cleaned with an optic cleaning brush. To remove sticky emulsion deposits, please use an optic tissue, moistened with pure alcohol. • Do not use solvents for cleaning! • Do not loosen the paint-secured screws! Product Identification Please always refer to the model type and unit serial number when ordering spare parts or requesting information. Explanation of the Symbols e photo refers to objects identified by pictures, photos or graphs. 3.General Product Information The LOCPRO 35 is a lightweight mobile projector for on- locatio...