Оценок - 1, средний балл: 5
(
)
)
|
Фрагмент инструкции
B461518_ER2301_Tori_EU
3
08-04-23
11:30:19
This Beard/Hair Trimmer is for the
J Cleaning Lever
Operation
Button. (See Fig.3)
trimming and care of mustaches,
Push this lever to remove bits of
beards and hair.Trimming length
hair caught between the station-
Rechargeable-battery operation
Notes on thinning
can be adjusted between 2 to
ary blade and the moving blade.
Charge the battery by plugging the For thinning, confirm that the thin-
1 8 m m . T h e T r i m m e r c a n b e
K Blade Block
Trimmer into an AC source using ning plate is set to the 1/3 (right)
operated either from an AC power
Release to remove the blade
the adapter. The switch should be position.Incorrect setting may result
source or on its own rechargeable
block from the housing to clean
set to 0·CHARGE during charging. in excessive cutting.
battery.
or replace the blade. (See Fig.
An 8-hour charge will provide ap-
If a difference in level is produced,
prox. 30 minutes of use.
lightly thin to compensate.
Parts identification
9)
L Adapter
If thick and thin portions are pro-
(See Fig. 1)
AC operation
Use this to connect the Trimmer
duced, or if there are portions with
A Switch
to an AC power source for re-
Plug the Trimmer into an AC power an excessive amount of hair, thin
Slide up to turn on, slide down
charging or for AC operation.
source using the adapter with the the appropriate portions to com-
to turn off.
switch set to 0·CHARGE.Wait pensate.
M Oil
B Charging Indicator Lamp
Lubricate the space between
about 10 seconds, then switch the Point:
Lights when the unit is con-
the stationary and moving blade
trimmer on. After use, return the Thin the hair gradually while check-
nected with the adapter L to an
with 2 or 3 drops of oil after use.
switch to the 0·CHARGE position.
ing the overall balance.
AC power source for charging.
(See Fig. 11)
Trimming of Beard
Maintenance
C Main Blade
N Cleaning Brush
A precision 39mm-wide blade
Place the angled face of the comb Blades
which can be used with the
against the skin and cut the beard 1. Brush out the cutting mecha-
comb attachment
by moving the trimmer in all direc-
G .
Trimming length indicator
tions to obtain a uniform cut. (See
nism. (See Fig. 8)
D Thinning Plate
Fig. 5)
2. Hold body of the trimmer with
When thinning,slide the thinning
Indicator
Trimming Length
With curly facial hair, the comb
Panasonic mark upwatds, place
plate up until it firmly clicks in
attachment may not cut all of the
the thumb against the blades,
position. (See Fig. 2)
1
2.0mm
hair. In this case, remove the comb
and push them away from the
E Thinning Plate Lock Button
●
3.0mm
attachment and use a conventional
main body. (See Fig. 9)
Press and hold while sliding the
comb to draw out the remaining 3. Push down the cleaning lever
Thinning plate D down to set
2
4.5mm
uncut hair.
to raise the moving blade and
the Thinning Plate back to its
(See Fig. 6)
brush in between the blades.
original position.
●
6.0mm
When shaping the beard, remove
(See Fig. 10)
F Dial
4. Put a few drops of oil on the
3
7.5mm
the comb attachment. Place the
Turn the dial to a higher set-
angled edge against the skin and
blades. (See Fig. 11)
ting to raise or lower the comb
●
9.0mm
make the border of the beard even.
Blade Life
attachment G to the desired
length (between 2 and 18mm).
4
10.5mm
How to use the thinning function
Blade life will vary according to
the frequency and length of use.
G Comb Attachment
●
12.0mm
(See Fig. 7)
Use this to control the trimming
First, slide the Thinning plate up For example, using the unit for 10
length. (See Fig. 4) Be sure to
5
13.5mm
to “1/3” until it clicks. (See Fig. 2) minutes every 3 days, the life ex-
slide the Thinning plate down to
While applying the blade point at pectancy is approximately 3 years.
“1” before attaching the attach-
●
15.0mm
right angles to the hair, run the If cutting efficiency is reduced sub-
ment. (See Fig. 3)
trimmer slowly across the head as stantially despite proper mainte-
6
16.5mm
nance, the blades have exceeded
H Stationary Blade
if combing the hair. After thinning,
slide the thinning plate back while their service life and should be
I Moving Blade
●
18.0mm
pushing the Thinning Plate Lock changed. The replacement part
no. is ER965.
4
5
Refine_P00-07_EN_ER2301_004.p1.pdf
Refine_P00-07_EN_ER2301_005.p1.pdf
Refine_08-04-04
10:36:40
Refine_08-04-04
10:36:40
P00-07_EN_ER2301.indd 4
2008/04/04 10:31:25
2008/04/04 10:31:25
P00-07_EN_ER2301.indd 5
2008/04/04 10:31:26
2008/04/04 10:31:26
...