Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Vertical Arm must clear door opening.Center lift in door opening. Side to Side Alignment Align(Parallel) Align(Parallel) Lift towers and vertical arms must be parallel (aligned) with vertical sides of door jamb andperpendicular (90.) to the vehicle floor. Figure B Installation Kit 30955K suppliedin lift parts box. Detailed instructions supplied in kits. Figure C Edge of Finished Floor or Stepwell Filler(not outboard edge of vehicle) Inboard Edge of Threshold Warning (Top) Plate(with plate folded down) Minimum perFMVSS No. 403 18"18" Vehicle Side Door Rear Door Rear Door Ford 30956K 30957K 30970K-42 GM/Chevy 30958K Extended LengthChassisStandard Length Chassis Installation Kits *30959K *30981K * Rear BumperReplacement Kit19395A96 required. “DOT — Private Use Lift” NHTSA Vehicle Physical Requirements B A C Figure A Door Opening Dimensions Vehicle lift access door opening must meet specified dimensions. Braun Corporation FMVSS No. 403 Quick Reference Installation Sheet 32494 OEM (Van) Chassis Floor Requirements Nonmodified OEM full size floors meet all requirements. Alternative floor structures are allowed providing the installed liftsystem passes all FM- VSS 403 requirements. “DOT - Private Use Lift” verifies this platform lift meets only the “private use lift” requirements of FMVSS No. 403. This lift may be installed on all vehicles appropriatefor the size and weight of the lift, except forbuses, school buses, and multi-purposepassenger vehicles other than motor homeswith a gross vehicle weight rating (GVWR) that exceeds 4,536 kg (10,000 lb). Clear Door Opening Width Maximum Floor-to-Ground A B C 47" 40" 42" Minimum Clear Door Opening Height NVL955IB3144 Braun Corporation FMVSS No. 403 Quick Reference Installation Sheet 32494 7 1 4 6 5 3 2 8 Figure E Figure D WARNING Check for obstructions such as gas lines, wires, exhaust, etc. before drilling or cutting. Failure to do so may result in serious bodily injury and/or property damage. 1. Drill two mounting holes (holes 6 and 7). 2. Temporarily secure lift using two mounting bolts (holes 6 and 7). 3. Manually deploy lift and check lift clearance. Drill remaining mounting holes. 4. Install below floor mounting hardware per instructions supplied in kit. 5. Tighten mounting bolts per sequence detailed above. Note deflection detail below. Mounting Bolt Torque Target: 30 foot pounds. 2 Secure Lift To Correct: Dimensions MUST be Equal 90 90 To Correct: ® 29823 ® 29823 ® 29823 LOOSEN LOOSEN TIGHTEN LOOSEN TIGHTEN TIGHTEN TIGHTEN Loosen Tighten Tighten Tighten Loosen Loosen LOOSEN Note. All fasteners must meet FMVSS 571.403 Section 6.3. Chassis 1. Drill 1-1/8" diameter grommet access hole. Check under the vehicle for obstructions. 2. Insert grommet. Secure grommet with two self-tap screws. 3. Route ground and power cables through grommet. Route cables clear of exhaust, other hot areas and moving parts. 4. Connect ground and power cables. Ground Cable Corrosion: When mounting ground cables, remove undercoating, dirt, rust, etc. from framing member around mounting holes (minimum 5/8” diameter area). Apply protective coating to mounting holes to prevent corrosion. Failure to do so will void warranty of certain electrical components. Position and secure ground cable clear of lift operation. CAUTION Figure G 5/16" External Tooth Star Washer 5/16-18 x 3/4" Thread Cutting Screw 9/32" Diameter Pilot Hole Ground Cable Mounting 3 Attach Power and Ground Cables Figure F Ground Cables Pump mounted ground cable must be routed and mounted directly to a vehicle framing member. Failure to do so will void warranty of certain electrical components. Ground Cable to Chassis Battery Cable to Circuit Sentry Rubber Boot Star Washer 3/8" Hex Nut Power Feed Stud Floor Grommet Braun Corporation FMVSS No. 403 Quick Reference Installation Sheet 32494 Vehicle and Lift Interlocks The pump module is equipped with a lift interface 9-circuit connector (female socket). A mating 9-circuit connector (male plug) is supplied. To meet minimum NHTSA requirements, connect to vehicle interlock harness as outlined below (Steps 1-5) Optional Interlock Kits Universal Interlock Kit 30940K is available for easy interface with vehicle OEM electronic signals. Instrument Panel Display Kit 30938K provides an LED Panel Display that interfaces with Braun Universal Interlock Kit 30940K. Detailed installation instructions are supplied with interlock kits. Note: All Braun Corporation interlocks require a positive (+12V) Lift Stowed signal (Pin 7). INTERLOCK CONNECTOR - P21 6 5 4 3 2 1 NO. SIGNAL DEFINITION 9-COND WIRE CODE 78 9 VEHICLE SECURE (INPUT) NOT USED NOT USED NOT USED NOT USED NOT USED LIFT STOWED (+12V) NOT USED LIFT STOWED (GND) 6 5 4 3 2 1 9 8 7 3 2 1 6 5 4 9 8 7 To Interlock Disconnect 2 1 5 Disconnect and remove eye terminal Lift Pump Module Connect 4 Connect vehicle interlock signal wires 3 Install 31798A in cavity 7 (+) or 9 (-) Shipped As VEHICLE SECURE SIGNAL (Grey/Red) LIFT STOWED SIGNAL (Yellow/Light Blue...