Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
It requires two people to assemble and move the appliance. . During assembly the appliance becomes heavier and more difficult to move.We therefore advise you to assemble the appliance at the place where it will be used. Make sure there is enough free space beside (at least 50 cm) and behind (at least 30 cm) the appliance. . If the couch and/or canopy have to be placed on the floor, put them on the floor with the tube lamps facing downwards to avoid internal damage. Make sure you place them on a soft surface (e.g. a carpet or rug) to prevent damage to the housing (fig. 2). ENGLISH 7 1 First assemble the legs of the frame by fastening the angle sections with the bolts and then fit the side panels, if applicable (fig. 3). . NB: the holes in the side panels must be on the front side. 2 Place the couch on the legs carefully. Make sure the legs slide steadily into the appropriate openings in the couch (fig. 4). . NB: the openings for assembling the canopy must be located at the back of the couch. 3 If necessary, you can move the couch slightly by sliding its legs across the floor or by carefully lifting it slightly off the floor together with another person. Make sure there is enough free space beside (at least 50 cm) and behind (at least 30 cm) the appliance. . Never try to move the appliance in the manner shown in the picture.This could cause the frame to become detached from the couch (fig. 5). 4 Lift the canopy together with another person and position its connecting tubes over the connecting holes. Slide the tubes steadily into the connecting holes of the couch (fig. 6). B Be careful not to get your fingers stuck between the couch and the canopy. B Make sure the cord does not get stuck between the couch and the canopy. 5 6 Remove the protective foil from the acrylic sheets of the canopy and couch (fig. 7). Plug the connecting cable into the socket in the couch (fig. 8). . If you want to remove the connecting cable, follow the instructions shown in the picture (fig. 9). 7 Place the front panel and fasten it with the screws (fig. 10). The only purpose of the panel is to enhance the appearance of the appliance. 8 Insert the mains plug into the wall socket. Using the appliance 1 Switch the appliance on by setting the required tanning time on the timer (fig. 11). B For the correct tanning times, see 'Tanning sessions: how often and how long?' 2 Push the canopy backwards so that you can lie down on the couch.When you are lying on the couch, pull the canopy back into horizontal position (fig. 12). B NB: when the appliance has not been used for some time, the hinges of the canopy may squeak when you open or close the canopy for the first time. 3 Switch the body cooler on by means of the switch (fig. 13). . Select the desired airflow: n or b (fig. 13). 4 HB589 only: if you like, you can also switch on the facial tanner (fig. 14). . Select , for 75% of the full intensity or m for full intensity (fig. 14). Don't forget to put on the protective goggles provided. During the last minute of the session you will hear a beeping sound. 5 6 Cleaning Always unplug the appliance and let it cool down before you start cleaning it. Do not use abrasives or scourers. Never use liquids such as alcohol, methylated spirits, petrol or acetone to clean the acrylic sheet as this may cause irreparable damage. ENGLISH . Clean the outside of the appliance with a damp cloth. B Do not let any water run into the appliance. Replacement The light emitted by the tanning lamps will become less bright in time (i.e. after a few years in case of normal use). When this happens, you will notice a decrease in the tanning capacity of the appliance.You can solve this problem by setting a slightly longer tanning time or by having the tanning lamps replaced. Have the tanning lamps and/or star ters replaced by a ser vice centre authorised by Philips. They have the knowledge and skills required for this job and the original spare par ts for your tanning appliance. . If you really insist on replacing the tube lamps and/or starters yourself, you should proceed as follows: Remove the mains plug from the wall socket. 1 2 3 4 5 Remove the end cover at the head of the canopy by undoing the screws (fig. 15). First pull the acrylic sheet approx. 10 cm out of the appliance (1).Then undo the snap strip on the rear side of the canopy (2) (fig. 16). Do the same with the snap strip on the front side of the canopy. Remove the acrylic sheet (fig. 17). . Now you can remove the tube lamps and the starters. B NB: you can now also clean the acr ylic sheet, if you wish. 6 7 8 9 The lamps and/or starters of the couch and the canopy can in principle be replaced in the same way.The starters are located at one of the lamp ends. To remove the lamps, turn them to the left or to the right so that you can lift them out of their holders. The starters can be removed by turning them to the left. Insert new lamps and/or starters and follow the instructions above in reverse direction and order...