Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
Primarily UV-B stimulates the production of a substance called "melanin", which is necessary for tanning. The effect does not show until a couple of days after the sunbath. -"Direct tanning". The UV-A and also a part of the visible light cause quicker browning without reddening or "getting sunburnt". 4 The face tanner This face tanner emits predominantly UV-A, and also a very small amount of UV-B. UV and your health After an excessive exposure to ultraviolet (from the natural sun or from your face tanner), the skin may develop sunburn. Beside numerous other factors, such as excessive exposure to the natural sun, improper and excessive use of your face tanner will increase the risk of skin and eye disease. The nature, intensity and duration of the radiation on one hand, and the sensitivity of the individual on the other, are decisive on the degree in which these affects can occur. The more skin and eyes are exposed to UV, the more risk increases of diseases such as inflammation of the cornea and/or conjunctiva, damaging of the retina, cataract, premature aging of the skin and skin tumours. Certain medicines and cosmetics increase the sensitivity to UV. Therefore, it is of great importance -that you follow the instructions in sections "Important" and "UV sessions: how often? And how long?"; -that you select the advised operational distance of 10 cm (approx. 4"); -that you do not exceed the maximum amount of tanning hours per year (i.e. 30 hours or 1800 minutes); -that you always wear the provided goggles while tanning. UV sessions: how often? And how long? You may have one UV session per day, over a period of five to ten days Allow at least 48 hours between the first two sessions. After such a course, you may rest the skin for a while. Approximately one month after a course your skin will have lost much of the tan. You might then decide to start a new course. On the other hand, it is also possible to have one or two UV sessions per week after a course has elapsed in order to keep up the tan. Whatever you may prefer, make sure that you do not exceed the maximum amount of tanning hours. For this face tanner the maximum is 30 hours (= 1800 minutes) per year. Example: Imagine that you take a 10 day UV course, with a 10 minute session on the first day and 25 minutes' sessions on the nine following days. The entire course then includes (1 x 10 minutes) + (9 x 25 minutes) = 235 minutes. Over a year you may have 7 of these courses. (As 7 x 235 minutes = 1645 minutes.) From the table it will be seen that the first session of a course should have a duration of 10 minutes. This is not dependent upon individual skin sensitivity. Duration of the UV session in minutes 1st session rest of2nd session 3rd session 4th session 5th session 6th session 7th session 8th session 9th session 10th session - for persons with very sensitive skin: 10 min. 410-15 10-15 10-15 10-15 10-15 10-15 10-15 10-15 10-15 - for persons with normal sensitive skin: 10 8 hours 20-25 20-25 20-25 20-25 20-25 20-25 20-25 20-25 20-25 - for persons with less sensitive skin: 10 30-40 30-40 30-40 30-40 30-40 30-40 30-40 30-40 30-40 • If you think that the sessions are too long for you • For a beautiful all-over tan, turn your face slightly (e.g. if the skin gets taut and tender after the session), during the session so that the sides of the face are we advise you to reduce the sessions by e.g. better exposed to the tanning rays. 5 minutes. 5 General description (fig. 1) A Tube lamps (type Philips Cleo 15 W) with starters (type Philips S2) B Reflectors C Timer D Ventilation openings E Mains cord F Memo knobs G Protective eye goggles (2x) (Type no. HB 071 / service no. 4822 690 80123 - illustrated -or type no HB 072 / service no. 4822 690 80147 - not illustrated -) How to use the face tanner -Insert the plug into a wall socket (220-240 V). -Refer to the table in these instructions for use and your personal memo (F) on the appliance or your own notes to determine the duration of the session. -Put on the supplied protective goggles (G). -Set the timer (C) to the session time. -Position yourself in front of the face tanner. The distance between your face and the tube lamps should be about 10 cm (= 4") fig. 2. -Once the set time has elapsed, the timer will switch off the appliance automatically. -Remove the plug from the wall socket after use. After the UV tanning session -Remove the plug from the wall socket. -On one of the session memos (F) you can note down how many sessions you have had. There are two such memos, for two users. Cleaning Always unplug the face tanner and let it cool down before cleaning. • You can clean the outside of the face tanner with a damp cloth. Make sure that no water runs into the appliance. • Do not use abrasives or scourers, or liquids such as petrol or acetone. Replacing the tube lamps and/or starters In the course of time (in normal family use after some years) the efficiency of the tube lamps will gradually decrease. If this happens...